Panasonic BT-LH1850P Manual Do Utilizador

Página de 60
12
Controls and Their Functions 
(continued)
13
4
  MENU button, rotary knobs (with push-on switch (PIC-
TURE)) and RETURN/VOLUME button (→page 15)
Use these buttons to display menus, select and adjust set-
tings and perform menu selections.
MENU:  Press  to  display  the  TOP  MENU  (main  menu, 
FUNCTION menu and INPUT SELECT menu) or to 
exit from a menu.
Rotary knob:
 
 
 Turn the knob clockwise or counterclockwise to move 
the cursor up or down or to change set values. 
 
 
 Press the knob to start changing set values, to con-
firm them and to open submenus.
RETURN:
 
 
 Press to return to the previous menu or cancel to re-
cover a previously set value.
When no menu is open, press the rotary knob or RETURN 
button to open a menu other than the TOP MENU.
PICTURE:
 
 
 When no menu is displayed, press the rotary knob to 
open the picture adjusting menu. (→page 15)
VOLUME:
 
 
 When no menu is displayed, press the RETURN but-
ton to open the audio volume bar meter. (→page 15)
5
  Speaker (monaural)
Enables monitoring of analog AUDIO, SDI and HDMI signal 
inputs.
• Connecting headphones to the HEADPHONES output jack 
turns off the speaker.
6
  HEADPHONES output jack (M3 stereo mini jack)
Allows you to connect headphones to monitor analog audio, 
SDI and HDMI signal input.
• The  volume  and  sound  quality  differ  depending  on  the 
headphones.
Rear panel
DVI-I
SDI 
VIDEO
AUDIO
GPI
RS-485
SWITCHED
OUT
IN
1
2
IN
IN
R
L
IN
OUT
RS-232C
OUT
1
2
6
8
5
3
4
7
1   SDI terminal (BNC)
IN1:  This is the SDI input terminal (compatible with HD/SD 
automatic switching).
IN2:  This is the SDI input terminal (compatible with HD/SD 
automatic switching).
SWITCHED OUT: This is the active through-out terminal for 
the  SDI  input  signal  being  displayed  on 
the screen.
• Active SDI through-out is only output when [SDI1] or [SDI2] 
is selected using [INPUT SELECT]. It is not output when 
something other than SDI is selected. Embedded audio is 
also supported.
When this output is used to daisy-chain
*
1
 multiple monitors, 
the quality of the original signal, cable length, the number 
of connected devices and other factors all come into play to 
deteriorate picture quality and introduce noise.
*
1
 
Daisy-chain:
Refers to connecting the through-out signal from a device 
to the input of a second, third or more devices in a linear 
series, thus using a single signal in multiple devices.
• Use a 5C-FB or equivalent cable to make connections to 
an SDI terminal.
2   VIDEO terminal (BNC) 
*
2
*
3
IN:  
 This is the VIDEO signal (composite signal) input ter-
minal.
OUT:  This is the input signal through-out terminal.
*
2
 
Unless a cable is connected to the OUT terminal, the VID-
EO IN terminal is automatically terminated at 75 Ω. Con-
necting a cable releases this termination.
*
3
 
Since  a  connection  to  the  through-out  terminal  releases 
the 75 Ω termination of the unit, the level of the VIDEO 
signal input to the unit may become too large depending 
on the connected device.
3   DVI-I terminal (single link)
This is the DVI-signal input terminal.
• Use  double  shielded  cable  for  making  connections  to  a 
DVI-I terminal.
4   HDMI terminal (Type A)
This is the HDMI input terminal.
• Use  double-shielded  cable  for  making  connections  to  an 
HDMI terminal.
5   AUDIO input terminal (pin jack)
This is the common audio input terminal for all video input 
terminals.
• Use shielded cable for making connections to an AUDIO 
input terminal.
6   RS-485 input/output terminal (RJ-45)
External control is possible by using an RS-485 signal.
• Use shielded cable for making connections to an RS-485 
input/output terminal.
• Make sure that the cable is fully inserted in the terminal and 
that it cannot easily be pulled out.
• A loop-through connection using the RS-485 IN/OUT termi-
nals allow operation of multiple monitors (up to 32 monitors) 
connected to the RS-485 IN/OUT terminals.
• Connect a terminator (120 Ω) between the first and second 
pin of the OUT terminal on the last monitor in the chain.
7   GPI input terminal (D-SUB, 9 pins)
External control is possible by using a GPI signal.
• Use shielded cable for making connections to a GPI input 
terminal.
8   RS-232C input terminal (D-SUB, 9 pins)
External control is possible by using a RS-232C signal
• Use shielded cable for making connections to an RS-232C 
input terminal.