Panasonic BT-LH1850P Manual Do Utilizador

Página de 60
44
45
REMOTE Specifications 
(continued)
Assigned item
Function
Operating conditions
PIXEL TO PIXEL
Switches screen display between input size and display 
size.
Level operation
(Short-circuited: ON, Open: OFF)
FOCUS-IN-RED
Displays the outlines of the subject that are in focus in 
red
Level operation
(Short-circuited: ON, Open: OFF)
REMOTE STANDBY
 
*
4
*
5
Sets REMOTE STANDBY (the backlight is turned off).
Level operation
(Short-circuited: ON, Open: OFF)
*
4
 
When remote standby is set to ON, the front power LED flashes.
*
5
 
If the GPI input terminal to be assigned is set to a short-circuited state first and then MENU is operated to set this item, the backlight 
turns off and the screen display disappears, so MENU operation becomes unable to be checked. To change the setting of this item, 
be sure to set it when the GPI input terminal is in the open state.
Restrictions
• “SD ASPECT” does not operate when the input signal is HD.
• “SD ASPECT”, “SCAN”, “WFM/VECTOR”, “MARKER”, and “PIXEL TO PIXEL” do not operate in SUB WINDOW mode.
• “SCAN” and “MARKER” do not operate in PIXEL TO PIXEL mode.
• “GAMMA SELECT”, “SD ASPECT”, “SCAN”, “MARKER”, and “MONO” do not operate when the input line of the signal is HDMI and 
the signal format is 640 x 480.
„
„
Priority of assigned functions
• When both “MARKER1” and “MARKER2” are activated at the same time, “MARKER1” has priority. However, when the display as-
pect ratio is 4:3, the “MARKER1” aspect ratio is 16:9 and the “MARKER2” aspect ratio is 4:3, “MARKER2” is displayed. In this case, 
the “MARKER2” background is controlled.
• When “MARKER BACK HALF” and “MARKER BACK BLACK” are activated at the same time, “MARKER BACK BLACK” has priority.
• When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are activated at the same time, “GAMMA SEL. FILM” has priority.
RS-232C input terminal
External operations can be performed via the RS-232C interface.
Regarding the pin arrangement and connections of the RS-232C input terminal, refer to the diagram below and the table below right.
For details on systems using RS-232C input terminal, be sure to consult your dealer.
„
„
Connectors and signals
Connector: D-SUB 9-pin (female)
Signal
Pin number
Signal
Description
1
N.C.
Not connected
2
TXD
Transmission data
3
RXD
Reception data
4
DSR
Connected inside
5
GND
Ground
6
DTR
Connected inside
7
CTS
Connected inside
8
RTS
Connected inside
9
N.C.
Not connected
„
„
Communication parameters
Signal level
RS-232C compliant
Synchro system
Asynchronous
Transfer rate
9600 bps
Parity
None
Data length
8 bit
Stop bit
1 bit
Flow control
None
„
„
Command format
STX (02h) 
Command :
Data
ETX (03h) 
• The command is the 3-character string starting with STX and 
ending with ETX.
• Append any data after the colon (:) following the command, as 
required.
„
„
Response formats
1. 
Setting command response
STX (02h) 
Command
ETX (03h) 
2. 
Query command response
STX (02h) 
Data
ETX (03h) 
3. 
Error response
STX (02h) 
Error codes
ETX (03h) 
Error codes
ER001: Invalid command
ER002: Parameter error
RS-232C terminals (9P) 
External Device Side
(Straight)
This unit Side
Pin number Signal
Pin number Signal
1
N.C.
1
N.C.
2
RXD
2
TXD
3
TXD
3
RXD
4
DTR
4
DSR
5
GND
5
GND
6
DSR
6
DTR
7
RTS
7
CTS
8
CTS
8
RTS
9
N.C.
9
N.C.