MTD 465 Manual Do Utilizador
8
Hopper Assembly
Allow leaves and small branches up to 1/2 diameter to
be fed into the impeller for chipping and shredding.
Material can be raked into hopper assembly by
lowering the hopper assembly. See Figure 6.
be fed into the impeller for chipping and shredding.
Material can be raked into hopper assembly by
lowering the hopper assembly. See Figure 6.
Tamper Plug
(If Equipped)
The tamper plug is designed to insert in the chipper
chute to push material toward the impeller.
See Figure 6.
chute to push material toward the impeller.
See Figure 6.
SECTION 4: OPERATING YOUR CHIPPER SHREDDER
WARNING: The operation of any chipper
shredder can result in foreign objects
being thrown into the eyes, which can
damage your eyes severely. Always wear
the safety glasses provided with this unit
or eye shields before chipping or shred-
ding and while performing any
adjustments or repairs.
shredder can result in foreign objects
being thrown into the eyes, which can
damage your eyes severely. Always wear
the safety glasses provided with this unit
or eye shields before chipping or shred-
ding and while performing any
adjustments or repairs.
Gas And Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the separate engine manual packed with your chipper
shredder. Read instructions carefully.
the separate engine manual packed with your chipper
shredder. Read instructions carefully.
WARNING: Never fill fuel tank indoors with
engine running or until the engine has
been allowed to cool for at least two
minutes after running.
engine running or until the engine has
been allowed to cool for at least two
minutes after running.
Starting Engine
•
Attach spark plug wire to spark plug. Make certain
the metal cap on the end of the spark plug is
fastened securely over the metal tip on the spark
plug.
the metal cap on the end of the spark plug is
fastened securely over the metal tip on the spark
plug.
•
Engines with choke lever:
Move choke lever on engine to CHOKE position. (A
warm engine may not require choking).
Move choke lever on engine to CHOKE position. (A
warm engine may not require choking).
•
Engines with primer:
Prime engine as instructed in separate engine
manual.
Prime engine as instructed in separate engine
manual.
•
The throttle control lever is located on the engine.
Move engine throttle control lever to FAST or
START position.
Move engine throttle control lever to FAST or
START position.
•
Grasp starter handle and pull rope out slowly until
engine reaches start of compression cycle (rope
will pull slightly harder at this point).
engine reaches start of compression cycle (rope
will pull slightly harder at this point).
NOTE: A noise will be heard when finding the start of
the compression cycle. This noise is caused by the
flails and fingers, which are part of the shredding mech-
anism, and it should be expected until the impeller
reaches full speed.
the compression cycle. This noise is caused by the
flails and fingers, which are part of the shredding mech-
anism, and it should be expected until the impeller
reaches full speed.
•
Pull rope with a rapid, continuous, full arm stroke.
Keep a firm grip on starter handle. Let rope rewind
slowly.
Keep a firm grip on starter handle. Let rope rewind
slowly.
•
Repeat the previous steps until engine fires. When
engine starts, move choke control (if equipped)
gradually to RUN position.
engine starts, move choke control (if equipped)
gradually to RUN position.
WARNING: Never run the engine indoors
or in a poorly ventilated area. Engine
exhaust contains carbon monoxide, an
odorless and deadly gas.
or in a poorly ventilated area. Engine
exhaust contains carbon monoxide, an
odorless and deadly gas.
Stopping Engine
•
Move throttle control lever to STOP or OFF
position.
position.
•
Disconnect spark plug wire from spark plug and
ground against the engine.
ground against the engine.
NOTE: See your engine manual packed with your unit
for more detailed instructions.
for more detailed instructions.
To Empty Bag
•
Un-clip drawstring and loosen bag from discharge
chute opening.
chute opening.
•
Empty bag and reattach to the discharge chute
opening. Pull on the drawstring until the bag is tight
around the chute opening and clip the drawstring
tight against the discharge chute.
opening. Pull on the drawstring until the bag is tight
around the chute opening and clip the drawstring
tight against the discharge chute.
Lowering The Hopper Assembly
•
With one hand grasp the handle at the top of the
hopper assembly and lift slightly.
hopper assembly and lift slightly.
•
With the other hand pull out on the release rod and
lower the hopper assembly to the ground.
See Figure 7.
lower the hopper assembly to the ground.
See Figure 7.
Figure 7
Hopper
Assembly
Assembly
Release
Rod
Rod