Poulan DB18542YT Manual Do Utilizador
23
SERVICE AND ADJUSTMENTS
02141
TO REPLACE HEADLIGHT BULB
• Raise hood.
• Pull bulb holder out of the hole in the backside of the
• Pull bulb holder out of the hole in the backside of the
grill.
• Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
• Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the
Repair Parts section.
HOOD
HEADLIGHT WIRE
CONNECTOR
CONNECTOR
FIG. 26
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 26)
(See Fig. 26)
• Raise hood.
• Unsnap headlight wire connector.
• Stand in front of tractor. Grasp hood at sides, tilt toward
• Unsnap headlight wire connector.
• Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
• To replace, reverse above procedure.
ENGINE
TO AD JUST THROTTLE CON TROL CABLE
The throttle control has been preset at the factory and
ad just ment should not be necessary. If adjustment is nec-
es sary, see engine manual.
ad just ment should not be necessary. If adjustment is nec-
es sary, see engine manual.
TO AD JUST CHOKE CON TROL
The choke control has been preset at the factory and ad-
just ment should not be necessary. If adjustment is neces-
sary, see engne manual.
just ment should not be necessary. If adjustment is neces-
sary, see engne manual.
TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.
fuse holder is located behind the dash.
REPLACING BATTERY (See Fig. 25)
WARNING: Do not short battery
ter mi nals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connect-
ing battery, remove metal bracelets,
wristwatch bands, rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from ac ci -
den tal grounding.
ter mi nals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connect-
ing battery, remove metal bracelets,
wristwatch bands, rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from ac ci -
den tal grounding.
• Lift hood to raised position.
• Remove terminal guard.
• Disconnect BLACK battery cable then RED battery
• Remove terminal guard.
• Disconnect BLACK battery cable then RED battery
cable and carefully remove battery from tractor.
• Install new battery with terminals in same position as
old battery.
• Reinstall terminal guard.
• First connect RED battery cable to positive (+) battery
• First connect RED battery cable to positive (+) battery
terminal with hex bolt and keps nut as shown. Tighten
securely.
securely.
• Connect BLACK grounding cable to negative (-) bat tery
terminal with remaining hex bolt and keps nut. Tighten
securely
securely
• Close terminal access doors.
• Close hood.
• Close hood.
0217
9
HEX BOLT
KEPS NUT
POSITIVE
(RED)
CABLE
(RED)
CABLE
NEGATIVE
(BLACK)
CABLE
(BLACK)
CABLE
TERMINAL
GUARD
GUARD
TERMINAL
ACCESS
DOOR
ACCESS
DOOR
FIG. 25