Exmark VT730EKC524 Manual Do Utilizador
Maintenance
5. Move the right side motion control lever to the
center, operating position.
6. Continue holding the right side motion control
lever in the center, operating position and pull up
on the blade control switch (PTO) and release.
The clutch should engage and the mower blades
begin rotating.
on the blade control switch (PTO) and release.
The clutch should engage and the mower blades
begin rotating.
7. Move or release the right side motion control
lever into the neutral position. The blades
should stop rotating and the engine should
continue running.
should stop rotating and the engine should
continue running.
8. Push the blade control switch down and move
the right side motion control lever to the center,
operating position.
operating position.
9. Continue holding the right side motion control
lever in the center, operating position and pull up
on the blade control switch (PTO) and release.
The clutch should engage and the mower blades
begin rotating.
on the blade control switch (PTO) and release.
The clutch should engage and the mower blades
begin rotating.
10. Push the blade control switch (PTO) down to the
off position. The blades should stop rotating.
11. With the engine running, pull up the blade control
switch (PTO) and release without holding right
side motion control lever to the center, operating
position. The blades should not rotate.
side motion control lever to the center, operating
position. The blades should not rotate.
Check for Loose Hardware
Service Interval: Before each use or daily
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Visually inspect machine for any loose hardware
or any other possible problem. Tighten hardware
or correct the problem before operating.
or correct the problem before operating.
Service Air Cleaner
Service Interval: Every 250 hours—Replace
the primary air cleaner
element — check
secondary air cleaner
element; replace if dirty.
(May need more often
under severe conditions.
See the Engine manual for
additional information.)
element — check
secondary air cleaner
element; replace if dirty.
(May need more often
under severe conditions.
See the Engine manual for
additional information.)
Every 500 hours—
Replace the secondary
Replace the secondary
air cleaner element. (May
need more often under
severe conditions. See
the Engine manual for
additional information.)
need more often under
severe conditions. See
the Engine manual for
additional information.)
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. See the Engine Owner's Manual for maintenance
instructions.
Change Engine Oil
Service Interval: After the first 5 hours
Every 100 hours (May
need more often under
severe conditions.)
need more often under
severe conditions.)
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Drain oil while engine is warm from operation.
3. The oil drain hose assembly is located on the left
side of the engine.
Place pan under machine to catch oil. Remove oil
drain plug. Allow oil to drain and replace oil drain
plug. Torque plug to 20-24 ft-lb (27-33 N-m).
drain plug. Allow oil to drain and replace oil drain
plug. Torque plug to 20-24 ft-lb (27-33 N-m).
4. Replace the oil filter per the Engine Owner's
Manual. Clean around the oil filter and carefully
remove the filter by unscrewing it. Make sure no
oil drains onto the belt drive or clutch through
the holes in the engine deck. Before the new
filter is installed, apply a thin coating of Exmark
4–Cycle Premium Engine Oil on the surface of
the rubber seal. Turn filter clockwise until rubber
seal contacts the filter adapter, then tighten filter
an additional 2/3 to 3/4 turn.
remove the filter by unscrewing it. Make sure no
oil drains onto the belt drive or clutch through
the holes in the engine deck. Before the new
filter is installed, apply a thin coating of Exmark
4–Cycle Premium Engine Oil on the surface of
the rubber seal. Turn filter clockwise until rubber
seal contacts the filter adapter, then tighten filter
an additional 2/3 to 3/4 turn.
5. Clean around oil fill cap and remove cap. Fill to
specified capacity and replace cap.
6. Use oil recommended in the Check Engine Oil
Level section. Do Not overfill. Start the engine
and check for leaks. Stop engine and recheck oil
level.
and check for leaks. Stop engine and recheck oil
level.
7. Wipe up any spilled oil from engine deck
mounting surfaces.
Check Hydraulic Oil Level
Service Interval: Every 50 hours
31