Ariens 961465 Manual Do Utilizador
14
Lower
handle
handle
ROTATE
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase en gine speed
or it may result in personal injury. If you
believe that engine is running too fast or
too slow, take your mower to a qualified
service cen ter for repair and ad just ment.
Your engine speed has been factory set.
Do not attempt to increase en gine speed
or it may result in personal injury. If you
believe that engine is running too fast or
too slow, take your mower to a qualified
service cen ter for repair and ad just ment.
CARBURETOR
Your carburetor is not adjustable. If your
engine does not operate properly due to
suspected carburetor problems, take your
lawn mower to a qualified service center
for repair and/or ad just ment.
IMPORTANT: Never tamper with the
engine governor, which is factory set for
proper engine speed. Over speed ing the
engine above the factory high speed set-
ting can be dangerous. If you think the
engine-governed high speed needs ad-
justing, contact a qualified service center,
which has proper equip ment and ex pe ri-
ence to make any nec es sary adjustments.
Your carburetor is not adjustable. If your
engine does not operate properly due to
suspected carburetor problems, take your
lawn mower to a qualified service center
for repair and/or ad just ment.
IMPORTANT: Never tamper with the
engine governor, which is factory set for
proper engine speed. Over speed ing the
engine above the factory high speed set-
ting can be dangerous. If you think the
engine-governed high speed needs ad-
justing, contact a qualified service center,
which has proper equip ment and ex pe ri-
ence to make any nec es sary adjustments.
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
1. Remove upper handle and wire tie(s)
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
1. Remove upper handle and wire tie(s)
securing cable(s) to lower handle.
2. Remove hairpin cotters from lower
handle bracket mount ing pin.
3. Squeeze lower handle in to remove it
from mounting pins.
4. Turn lower handle over to raise or
lower handle.
5. Squeeze lower handle in and position
holes onto mount ing pins on handle
bracket.
bracket.
6. Reassemble upper handle and all
parts removed from lower handle.
STORAGE
Immediately prepare your lawn mower for storage at the end of the season or if the unit
will not be used for 30 days or more.
will not be used for 30 days or more.
2. Lubricate as shown in the Main te-
nance section of this manual.
3. Be sure that all nuts, bolts, screws,
and pins are securely fas tened. In-
spect moving parts for damage, break-
age and wear. Replace if necessary.
spect moving parts for damage, break-
age and wear. Replace if necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thor oughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
period of time, clean it thor oughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
“CLEANING” in the Maintenance sec-
tion of this manual).
tion of this manual).
Mowing
position
position
Mowing
position
position
HIGH POSITION
LOW POSITION
Handle
bracket
bracket
Hairpin
cotter
Mounting
pin
cotter
Mounting
pin
Lower handle
Handle
bracket
bracket
Hairpin cotter
SQUEEZE
TO ADJUST
Mounting pin