American Standard 2908.002 Folheto
REMINISCENCE™ DROP-IN
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
REMINISCENCE DROP-IN WHIRLPOOL &
BATHING POOL
BATHING POOL
❏
2908.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Sculptured rim design w/raised headrest
• Dual, molded-in arm rests
• Faucet deck/accessory area at drain end
• 1.5 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
• Eight multi-directional and flow-adjustable jets
• Pre-leveled tub bottom
• Sculptured rim design w/raised headrest
• Dual, molded-in arm rests
• Faucet deck/accessory area at drain end
• 1.5 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
• Eight multi-directional and flow-adjustable jets
including:
- Two Ideal-flow jets at foot area
- Four body massage jets
- Two recessed back-rest jets
- Four body massage jets
- Two recessed back-rest jets
• Deck-mounted, air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
❏
2908.018WC StayClean™ Whirlpool
Massage featuring System I
Massage featuring System I
• Same as 2908.018W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
Antimicrobial AlphaSan®
❏
2908.028W Whirlpool featuring System II
Same as 2908.018W except:
• 2.0 HP, two speed, self-draining pump/motor
with pulse feature
• Deck-mounted electronic control with 20
minute built-in timed safety shut off and
Chrome bezel
Chrome bezel
❏
2908.028WC StayClean™ Whirlpool
Massage featuring System II
Massage featuring System II
• Same as 2908.028W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
Antimicrobial AlphaSan®
❏
2908.002 Bathing Pool only
Nominal Dimensions: 66” x 36” x 24-1/4"
(1676 x 914 x 616mm)
© 2005 American Standard Inc.
BV-5
To Be Specified - Required:
❏ Color:
❏ Bath Faucet (Specify finish)
❏ Bath Drain: 1583.470 (Specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Jet Trim Ring Kit: 9860.200-two per kit (Specify finish)
for Body Massage Jets only
❏ System II Control Bezel: 9861.100 (Specify finish)
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
specifications shown on reverse side of page.
Rev. 10/05
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
For color/finish availability and other faucet choices, please see
the Product Selector and Pricing Guide.
the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to desired
bathing temperature.
temperature during operation. It will not heat cold water to desired
bathing temperature.