Casablanca Fan Company C3U72M Manual Do Utilizador
11
Send Signal
Fan Control
To start the fan. Press the selected speed button to run the fan at the desired speed.
1=Low speed 2=Medium speed 3=High speed
1=Low speed 2=Medium speed 3=High speed
To turn off the fan. Press the FAN OFF button.
Airfl ow Direction
To reverse the airfl ow press the REVERSE button. Reverse operates at any speed whether
fan is on or off . Th e fan returns to its set speed after reversing.
Light Control
Turn the light on or off independently from the fan by pressing the UP LIGHT DOWN
LIGHT OR BOTH button. (Th is is a rocker switch. Press the left side for the Down
Light, right side for the Up light , and the middle for both.) Keep pressing the button
in excess of 0.7 seconds, it becomes a dimmer. Th e light varies from ‘bright’ to ‘dim’ over
approximately 8 seconds. Th is sequence will reverse the light when it reaches the brightest
or dimmest level if you continue to hold the LIGHT button. Release the button when
the desired level is reached.
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains
the desired brightness level set previously.
If the fan is not functioning after installation:
1. Check to make sure that batteries are installed correctly in the
1. Check to make sure that batteries are installed correctly in the
control.
2. Turn the power off to the fan (from the circuit breaker) for at
2. Turn the power off to the fan (from the circuit breaker) for at
least FIVE seconds.
3. Turn the power back on (at the circuit breaker) and push the High,
3. Turn the power back on (at the circuit breaker) and push the High,
Medium, and Low buttons–in that order–within 20 seconds.
4. Th e fan should now function properly.
4. Th e fan should now function properly.
You will only have to change the dip switch settings in the remote if you are using more
than one fan in the same area and want to control them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for the fan you want to
Step 1. At the circuit breaker or fuse box, turn the power off for the fan you want to
change.
Step 2. Open the battery door of the Versa•Touch control and remove the battery.
Step 3. Change the dip switch settings, assuring that they are diff erent from the previously
Step 2. Open the battery door of the Versa•Touch control and remove the battery.
Step 3. Change the dip switch settings, assuring that they are diff erent from the previously
installed Versa•Touch fan.
Step 4. Re-install the battery and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back on for the fan whose
Step 4. Re-install the battery and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back on for the fan whose
frequency you are changing.
Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lo buttons (in
Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lo buttons (in
that order).
Note: All fans leave the factory set to ‘00000’.
Within 20 seconds of turning
the fan on, press in this order to
the fan on, press in this order to
set new frequency:
3 - HIGH
2 - MED
2 - MED
1 - LOW
1 - LOW
Circuit Breaker
or Fuse Box
press in this order to set new
frequency:
HIGH MED LOW
Dip Switch
Set to ‘01001’
Dip Switch
Set to ‘10000’
HELPFUL HINT: Label your controls to
ensure you do not mix them up.
WARNING: Do not turn the power off at the circuit breaker, then
back on, for the previously installed Versa•Touch 2 fan(s), as you
may inadvertantly change the frequency settings for it as well.
LOW
MED
HIGH
Fan
Off
Reverse
HIGH
IF FAN DOES NOT WORK
TRANSMITTER FREQUENCY SETTING
REMOTE OPERATION
Down
Light
Up
Light
versa•touch 2 control
(back)
MED
LO
LOW
LOW
HIGH
MEDIUM