Yamaha CVP - 405 Manual Do Utilizador
Appendix
CVP-405/403/401 Owner’s Manual
208
CVP-403: Keyboard Stand Assembly
CAUTION
• Be careful not to confuse parts, and be sure to install all
parts in the correct direction. Please assemble in accor-
dance with the sequence given below.
dance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below.
• Be sure to use the correct screw size, as indicated below.
Use of incorrect screws can cause damage.
• Be sure to tighten up
all screws upon com-
pleting assembly of
each unit.
pleting assembly of
each unit.
• To disassemble,
reverse the assembly
sequence given below.
sequence given below.
1
Open the package, take out marked “C” in the
illustration, take out the styrofoam pads, and
place the unit A on top of the pads.
illustration, take out the styrofoam pads, and
place the unit A on top of the pads.
Position the pads so that they will protect the headphone
jack located underneath the front left corner.
jack located underneath the front left corner.
2
Attach C to D and E.
3
Attach B.
Depending on the model of digital piano you purchased,
the surface color of one side of the rear panel may be dif-
ferent from the other side. In this case, position the rear
panel so that the side of the surface color similar to the
side panel (left) and the side panel (right) faces the player.
Depending on the model of digital piano you purchased,
the surface color of one side of the rear panel may be dif-
ferent from the other side. In this case, position the rear
panel so that the side of the surface color similar to the
side panel (left) and the side panel (right) faces the player.
1 Place the lower side of B on each foot of D and E, then attach
the upper side to D and E.
2 Attach the top of B to D and E by finger-tightening the thin
screws (4
✕ 12mm).
3 While pushing the lower part of D and E from outside, secure
the bottom ends of B using two tapping screws (4
✕ 20mm).
4 Insert the other two tapping screws (4 ✕ 20mm) into the
other two screw holes to secure B.
5 Securely tighten the screws on the top of B that were
attached in Step 3-
2.
4
Mount A.
Be sure to place your hands at least 10 cm
from either end of A when positioning it.
from either end of A when positioning it.
Have a Phillips-head (+) screw-
driver ready.
driver ready.
B
C
D
E
A
To prevent the key
cover from accidentally
opening during assem-
bly, press down on the
key cover, making sure
that the sheet (shown)
remain in place.
cover from accidentally
opening during assem-
bly, press down on the
key cover, making sure
that the sheet (shown)
remain in place.
Bundled pedal cord inside
Phones jacks
Styrofoam pads
AC power cord
Assembly Parts
6
✕ 25 mm long screws ✕ 4
6
✕ 16 mm short screws ✕ 4
4
✕ 12 mm thin screws ✕ 2
4
✕ 20 mm tapping screws ✕ 4
Cord holders
✕ 2
D
E
C
1
Untie and straighten out the
bundled cord attached to the
bottom of the C. Don’t discard the
vinyl tie, you’ll need it later in step 6.
bundled cord attached to the
bottom of the C. Don’t discard the
vinyl tie, you’ll need it later in step 6.
2
Use the four 6
✕ 25 mm long screws to attach C. First
attach one side panel, then attach the other side panel.
B
E
D
25
3
3
1
4
CAUTION
• Fingers can become pinched between A and C/D/E, be
extra careful so as not to drop A.
• Do not hold the keyboard in any position other than
the position shown in the illustration.
A
At least
10 cm