Yamaha CVP-208 Manual Do Utilizador
CVP-210/208
164
CVP-210/208: Keyboard Stand Assembly
CAUTION
■ Be careful not to confuse parts, and be sure to install all parts
in the correct direction. Please assemble in accordance with
the sequence given below.
the sequence given below.
■ Assembly should be carried out by at least two persons.
■ Be sure to use the correct screw size, as indicated below. Use
■ Be sure to use the correct screw size, as indicated below. Use
of incorrect screws can cause damage.
■ Be sure to tighten up all
screws upon completing
assembly of each unit.
assembly of each unit.
■ To disassemble, reverse
the assembly sequence
given below.
given below.
1
Remove all parts from the box. Confirm that all
parts shown in the illustration are provided.
parts shown in the illustration are provided.
2
With the key cover closed and the keyboard side
on the bottom, lean the unit against the wall.
on the bottom, lean the unit against the wall.
3
Remove the speaker box cover from the speaker box.
4
Attach the front legs.
5
Attach the rear leg.
6
Raising the unit to the standing position.
Use the front legs as support to raise the unit.
Use the front legs as support to raise the unit.
Main unit
Rear leg
Front leg (left)
AC power cord
Front leg (right)
Pedal box
5x18 mm fixing screws x16
Bundled pedal
cord inside
cord inside
CAUTION
• Be careful not to pinch your fingers.
• The top part of the music score stand is not fixed. When
• Be careful not to pinch your fingers.
• The top part of the music score stand is not fixed. When
you lean the unit against the wall, support the music score
stand with your hand so that the stand will not fall.
stand with your hand so that the stand will not fall.
Spread a large soft cloth, such as a
blanket, on the floor. Place the unit on
the cloth with the keyboard side on the
bottom and lean the unit against the wall
so that the unit will not fall or slip. Place
a soft cloth against the wall to protect
the instrument and wall from scratches.
blanket, on the floor. Place the unit on
the cloth with the keyboard side on the
bottom and lean the unit against the wall
so that the unit will not fall or slip. Place
a soft cloth against the wall to protect
the instrument and wall from scratches.
Be sure to
position the
keyboard side on
the bottom.
position the
keyboard side on
the bottom.
CAUTION
Please do not touch the speaker net.
Doing so may damage the speaker inside.
Please do not touch the speaker net.
Doing so may damage the speaker inside.
CAUTION
Do not place the main unit with the rear
side facing down.
Do not place the main unit with the rear
side facing down.
CAUTION
Do not lay the main unit upside-
down on the floor.
Do not lay the main unit upside-
down on the floor.
The speaker cover is attached to the
unit with two tabs and velcro tape
at several points. To remove the
speaker cover, pull them straight
down.
Be careful not to touch the speakers
when handling the speaker box.
Damage may result.
unit with two tabs and velcro tape
at several points. To remove the
speaker cover, pull them straight
down.
Be careful not to touch the speakers
when handling the speaker box.
Damage may result.
CAUTION
Put your hands at the positions indicated and pull as shown.
The speakers are located to either side of these places - avoid
touching the speakers as this may damage them.
Put your hands at the positions indicated and pull as shown.
The speakers are located to either side of these places - avoid
touching the speakers as this may damage them.
Front leg (right)
Front leg (left)
1
Fix the front right leg to
the bottom surface of the
unit using two screws.
the bottom surface of the
unit using two screws.
2
Fix the front right leg to
the speaker box using
three screws.
the speaker box using
three screws.
3
Fix the front left leg in the same way.
If the screw holes do not align, loosen the other screws and adjust
the position of the front leg.
the position of the front leg.
2
Fix the rear legs to the speaker box using two screws.
1
Fix the rear legs to
the bottom surface
of the unit using
two screws.
the bottom surface
of the unit using
two screws.
If the screw holes do not align, loosen the other screws and adjust
the position of the rear legs.
the position of the rear legs.
CAUTION
• Be careful not to pinch your fingers.
• When you raise the unit, do not hold the key cover.
• Be careful not to pinch your fingers.
• When you raise the unit, do not hold the key cover.
Have a Phillips-head (+)
screwdriver ready.
screwdriver ready.