Yamaha M2500 Manual Do Utilizador
The Scene Memory function
36
M2500—Owner’s Manual
Control change table
The M2500 is able to receive control change messages
from the MIDI IN connector to switch on/off the
ON/EDIT switches of the input channels, G1/A7–G8/
A14 section, and stereo/monaural master section.
When a control change number with a value in the
range of “0–63” is received, the ON/EDIT switch of
the corresponding channel will be turned “off,” and
when a value in the range of “64–127” is received the
switch will be turned “on.” Also, when you press an
ON/EDIT switch on the M2500 to turn it on/off, the
corresponding control change number will be trans-
mitted from the MIDI OUT connector with a value
of 127/0.
from the MIDI IN connector to switch on/off the
ON/EDIT switches of the input channels, G1/A7–G8/
A14 section, and stereo/monaural master section.
When a control change number with a value in the
range of “0–63” is received, the ON/EDIT switch of
the corresponding channel will be turned “off,” and
when a value in the range of “64–127” is received the
switch will be turned “on.” Also, when you press an
ON/EDIT switch on the M2500 to turn it on/off, the
corresponding control change number will be trans-
mitted from the MIDI OUT connector with a value
of 127/0.
When mute groups (page 37) are being used, control
change numbers 105–112 can be received and trans-
mitted to turn mute groups on/off. The same values
are used to indicate the on/off status as when turning
the ON/EDIT switches on/off.
change numbers 105–112 can be received and trans-
mitted to turn mute groups on/off. The same values
are used to indicate the on/off status as when turning
the ON/EDIT switches on/off.
The following table shows the M2500 channels (and
mute groups) that correspond to each control change
number.
mute groups) that correspond to each control change
number.
Note: If you wish to use control change messages
to switch M2500 channels or mute groups on/off,
make sure that the Utility mode item CC (control
change transmission/reception) is turned “on”
(this is the factory setting).
to switch M2500 channels or mute groups on/off,
make sure that the Utility mode item CC (control
change transmission/reception) is turned “on”
(this is the factory setting).
Control No.
Channel
Control No.
Channel
Control No.
Mute group
1
CH INPUT 1
36
CH INPUT 36
105
MUTE GROUP 1
2
CH INPUT 2
37
CH INPUT 37
106
MUTE GROUP 2
3
CH INPUT 3
38
CH INPUT 38
107
MUTE GROUP 3
4
CH INPUT 4
39
CH INPUT 39
108
MUTE GROUP 4
5
CH INPUT 5
40
CH INPUT 40
109
MUTE GROUP 5
6
CH INPUT 6
41
CH INPUT 41
110
MUTE GROUP 6
7
CH INPUT 7
42
CH INPUT 42
111
MUTE GROUP 7
8
CH INPUT 8
43
CH INPUT 43
112
MUTE GROUP 8
9
CH INPUT 9
44
CH INPUT 44
10
CH INPUT 10
45
CH INPUT 45
11
CH INPUT 11
46
CH INPUT 46
12
CH INPUT 12
47
CH INPUT 47
13
CH INPUT 13
48
CH INPUT 48
14
CH INPUT 14
49
ST CH INPUT 1
15
CH INPUT 15
50
ST CH INPUT 2
16
CH INPUT 16
51
ST CH INPUT 3
17
CH INPUT 17
52
ST CH INPUT 4
18
CH INPUT 18
53
CH INPUT 49
19
CH INPUT 19
54
CH INPUT 50
20
CH INPUT 20
55
CH INPUT 51
21
CH INPUT 21
56
CH INPUT 52
22
CH INPUT 22
57
CH INPUT 53
23
CH INPUT 23
58
CH INPUT 54
24
CH INPUT 24
59
CH INPUT 55
25
CH INPUT 25
60
CH INPUT 56
26
CH INPUT 26
61
G1/A7 OUT
27
CH INPUT 27
62
G2/A8 OUT
28
CH INPUT 28
63
G3/A9 OUT
29
CH INPUT 29
64
G4/A10 OUT
30
CH INPUT 30
65
G5/A11 OUT
31
CH INPUT 31
66
G6/A12 OUT
32
CH INPUT 32
67
G7/A13 OUT
33
CH INPUT 33
68
G8/A14 OUT
34
CH INPUT 34
69
STEREO OUT
35
CH INPUT 35
70
MONO/C OUT