Yamaha CP50 Manual Do Utilizador
Left & Right Parts
Song Setting Area
TRACK Part
MIC INPUT Part
Settings for All Parts
Settings for All Performances
40
CP5/CP50 Reference Manual
MIC INPUT Part (CP5 only)
This section provides a detailed description of the parameters used to configure the CP5’s MIC
INPUT part. The setting screen for this part contains two pages.
INPUT part. The setting screen for this part contains two pages.
Mic Effects Screen
From the Mic Effects screen, you can set parameters affecting the compressor, noise gate, and EQ
that act on audio signals input via the MIC INPUT jack. This screen contains a total of seven pages.
that act on audio signals input via the MIC INPUT jack. This screen contains a total of seven pages.
Edit Sequence
Press and hold the [MIC INPUT] button (for at least one second)
Navigate to the
required page using the [
L
PAGE] and [PAGE
R
] buttons
Turn or press Knobs 1 to 3
Page
On-screen name
(and full name)
Description
1
Volume
This parameter is used to adjust the part’s output level. It can also be set at any
time using the [MIC INPUT] knob on the control panel.
Setting values: 0 to 127
time using the [MIC INPUT] knob on the control panel.
Setting values: 0 to 127
Pan
This parameter is used to adjust the part’s stereo panning.
Setting values: L63 (far left) to C (center) to R63 (far right)
Setting values: L63 (far left) to C (center) to R63 (far right)
RevSend (Reverb
Send)
Send)
This parameter is used to set how much of the part’s output signal is sent to the
Reverb block. Higher values produce a more pronounced reverb sound.
Setting values: 0 to 127
Reverb block. Higher values produce a more pronounced reverb sound.
Setting values: 0 to 127
2
MicFx (Mic Effects)
By pressing Knob 1 on this page, you can open the Mic Effects screen (see
below) in order to configure the compressor, noise gate, and EQ that act on the
microphone input.
below) in order to configure the compressor, noise gate, and EQ that act on the
microphone input.
MicIns (Mic Insert
Effect)
Effect)
By pressing Knob 2 on this page, you can open the Mic Insert Effect screen
(page 41) in order to select and configure an insertion effect for the microphone
input.
(page 41) in order to select and configure an insertion effect for the microphone
input.
Edit Sequence
Press and hold the [MIC INPUT] button (for at least one second)
Navigate to Page 2
using the [PAGE
R
] button
Press Knob 1
Navigate to the required page using the
[
L
PAGE] and [PAGE
R
] buttons
Turn Knobs 1 to 3
Page
On-screen name
(and full name)
Description
1
NoiseSw
(Noise Gate Switch)
(Noise Gate Switch)
This parameter is used to turn on or off the noise gate for microphone input signals.
Setting values: on or off
Setting values: on or off
CompSw
(Compressor Switch)
(Compressor Switch)
This parameter is used to turn on or off the compression of microphone input sig-
nals.
Setting values: on or off
nals.
Setting values: on or off
2
NoisAtk
(Noise Gate Attack)
(Noise Gate Attack)
This parameter is used to set the amount of time that elapses between arrival of an
input signal and activation of the noise gate.
Setting values: 1ms to 40ms
input signal and activation of the noise gate.
Setting values: 1ms to 40ms
NoisRel
(Noise Gate
Release)
(Noise Gate
Release)
This parameter is used to set the amount of time over which the noise gate stops
silencing the input signal.
Setting values: 10ms to 680ms
silencing the input signal.
Setting values: 10ms to 680ms
NoisTh
(Noise Threshold)
(Noise Threshold)
This parameter is used to set the level at which the noise gate starts silencing the
input signal.
Setting values: -73dB to -30dB
input signal.
Setting values: -73dB to -30dB
3
CompAtk
(Compressor Attack)
(Compressor Attack)
This parameter is used to set the amount of time that elapses between arrival of an
input signal and activation of the compressor.
Setting values: 1ms to 40ms
input signal and activation of the compressor.
Setting values: 1ms to 40ms
CompRel
(Compressor
Release)
(Compressor
Release)
This parameter is used to set the amount of time over which the compressor stops
compressing the sound.
Setting values: 10ms to 680ms
compressing the sound.
Setting values: 10ms to 680ms