Yamaha PM5D-RH V2 Manual Do Utilizador
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual
Operating section
101
11
Monitor and Cue
Here we explain how you can use the MONITOR section
to monitor the desired source.
to monitor the desired source.
1
Make sure that your monitor system is con-
nected to the rear panel MONITOR OUT jacks
L/R/C.
If you want to monitor through headphones, make
sure they are connected to the top panel or front panel
PHONES jack.
nected to the rear panel MONITOR OUT jacks
L/R/C.
If you want to monitor through headphones, make
sure they are connected to the top panel or front panel
PHONES jack.
Note
• Since the DSP5D does not have monitor functionality, the
PM5D’s MONITOR section will always operate the monitor
settings of machine #1 (PM5D).
settings of machine #1 (PM5D).
• MONITOR OUT jack C is a special jack used to monitor the
center channel when LCR mode is active. Note that the
appropriate signal will not be output from MONITOR OUT
jack C unless the LCR channel is selected as the monitor
source and the USE AS CENTER BUS button is turned on
in the MIXER SETUP screen (SYS/W.CLOCK function)
(
appropriate signal will not be output from MONITOR OUT
jack C unless the LCR channel is selected as the monitor
source and the USE AS CENTER BUS button is turned on
in the MIXER SETUP screen (SYS/W.CLOCK function)
(
➥ p.222).
• Turning on the [CUE] key of even one input channel, output
channel, or DCA group will override the settings of the MON-
ITOR section and cause the Cue signal to be output from
the MONITOR OUT jacks. Make sure that the CUE section
[INPUT]/[DCA]/[OUTPUT] LEDs are not lit.
ITOR section and cause the Cue signal to be output from
the MONITOR OUT jacks. Make sure that the CUE section
[INPUT]/[DCA]/[OUTPUT] LEDs are not lit.
2
To specify the channel that will be selected by
the [DEFINE] key, press the DISPLAY ACCESS
section [MON/CUE] key repeatedly to access
the MONITOR screen shown below.
the [DEFINE] key, press the DISPLAY ACCESS
section [MON/CUE] key repeatedly to access
the MONITOR screen shown below.
3
Click a button in the DEFINE area to select the
channel that will be monitored when you
press the [DEFINE] key.
You can assign more than one channel to the
[DEFINE] key. You can choose from the following
sources.
channel that will be monitored when you
press the [DEFINE] key.
You can assign more than one channel to the
[DEFINE] key. You can choose from the following
sources.
Hint
The MONITOR screen also lets you make settings for monitor
signal delay, insert-out/in, and dimmer (
signal delay, insert-out/in, and dimmer (
➥ p.238).
4
Use the keys of the MONITOR section to select
the monitor source from the following.
the monitor source from the following.
Hint
• You can simultaneously select one from 2TR A1–2TR D3 or
DEFINE, and one from STEREO A/STEREO B (including
LCR) (a maximum of two). To select this from the panel,
simultaneously press the two corresponding keys on the
panel.
LCR) (a maximum of two). To select this from the panel,
simultaneously press the two corresponding keys on the
panel.
• The monitor source can also be selected in the MONITOR
screen (MON/CUE function).
5
Press the MONITOR [ON] key to turn it on.
Hint
A signal is always output from the PHONES jacks regardless
of the on/off state of the MONITOR [ON] key.
of the on/off state of the MONITOR [ON] key.
6
Turn the MONITOR [LEVEL] knob to adjust the
monitor level. If you are monitoring through
headphones, turn the PHONES [LEVEL] knob
to adjust the monitor level.
monitor level. If you are monitoring through
headphones, turn the PHONES [LEVEL] knob
to adjust the monitor level.
Hint
Monitor level and monitor on/off status can also be operated
from the STEREO/DCA strip section (
from the STEREO/DCA strip section (
➥ p.149).
7
If you want to monitor the signal in monaural,
turn the MONITOR section’s [MONO] key on.
turn the MONITOR section’s [MONO] key on.
MIX 1–MIX 24
Output signals of MIX channels 1–24
MATRIX 1–
MATRIX 8
MATRIX 8
Output signals of MATRIX buses 1–8
Monitoring a signal
MONITOR
DEFINE area
[2TR IN A1]/[2TR IN
A2] keys
A2] keys
The input signal from 2TR IN ANA-
LOG jacks 1/2
LOG jacks 1/2
[2TR IN D1]/[2TR IN
D2]/[2TR IN D3] keys
D2]/[2TR IN D3] keys
The input signal from 2TR IN DIGI-
TAL jacks 1–3
TAL jacks 1–3
[STEREO A]/[STE-
REO B] keys
REO B] keys
The output signal of the STEREO A/
B channels
B channels
[STEREO A] key +
[STEREO B] key
[STEREO B] key
The LCR channel output
[DEFINE] key
The signal pre-selected in the MON-
ITOR screen (MON/CUE function)
ITOR screen (MON/CUE function)