Yamaha PM5D-RH V2 Manual Do Utilizador
7
Using the Selected Channel section
68
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual
Operating section
H GATE [DECAY] encoder
Specifies the hold time of the gate (the time over which
the gate will close after the hold time has elapsed).
the gate will close after the hold time has elapsed).
I GATE [THRESHOLD] encoder
Specifies the threshold level of the gate (the level at
which the gate will open or close). The gate will open
when the signal exceeds this level, and will close when
the signal falls below this level.
which the gate will open or close). The gate will open
when the signal exceeds this level, and will close when
the signal falls below this level.
J GATE [RANGE] encoder
Specifies the amount of attenuation while the gate is
closed.
closed.
Here you can switch the on/off status of the signal sent
from the selected channel to the STEREO bus, and adjust
the pan.
from the selected channel to the STEREO bus, and adjust
the pan.
A STEREO [PAN] encoder
The function of this encoder depends on the currently
selected channel, as follows.
selected channel, as follows.
B [TO STEREO] key
The function of this key depends on the currently
selected channel, as follows.
selected channel, as follows.
Here you can edit compressor parameters for the selected
channel. This section is available only if a channel other
than an FX RTN channel is selected.
channel. This section is available only if a channel other
than an FX RTN channel is selected.
A COMP GR meter
This meter indicates the amount of reduction pro-
duced by the compressor of the selected channel.
duced by the compressor of the selected channel.
B COMP [ON] key
Switches the compressor on/off for the selected
channel.
channel.
C COMP [ATTACK] indicator
Indicates the attack time of the compressor in msec
units.
units.
D COMP [ATTACK] encoder
Specifies the attack time of the compressor (the time
from when the signal exceeds the threshold level until
compression begins).
from when the signal exceeds the threshold level until
compression begins).
E COMP [RELEASE] indicator
Indicates the release time of the compressor in msec
units or sec units (the indicator for the displayed unit
will light).
units or sec units (the indicator for the displayed unit
will light).
F COMP [RELEASE] encoder
Specifies the release time of the compressor (the time
from when the signal falls below the threshold level
until compression is removed).
from when the signal falls below the threshold level
until compression is removed).
G COMP [RATIO] indicator
Indicates the compression ratio setting.
H COMP [RATIO] encoder
Specifies the compression ratio (the ratio at which the
input signal will be compressed when the signal
exceeds the threshold level).
input signal will be compressed when the signal
exceeds the threshold level).
I COMP [THRESHOLD] encoder
Specifies the threshold level of the compressor (the
level at which the compressor will operate). The input
signal will start being compressed when the signal
exceeds this level; compression will be removed when
the signal falls below this level.
level at which the compressor will operate). The input
signal will start being compressed when the signal
exceeds this level; compression will be removed when
the signal falls below this level.
Selected channel
Function
Input channel
Adjusts the panning of the signal
sent from that channel to the STE-
REO bus.
sent from that channel to the STE-
REO bus.
ST IN channel
FX RTN channel
MIX channel
STEREO A/B channels
Adjusts the left/right balance of the
signal sent from the STEREO A/B
channels.
signal sent from the STEREO A/B
channels.
MATRIX channel
No function.
Selected channel
Function
Input channel
Functions as an on/off switch for
the signal sent from that channel
to the STEREO bus.
the signal sent from that channel
to the STEREO bus.
ST IN channel
FX RTN channel
MIX channel
STEREO A/B channels
No function.
MATRIX channel
STEREO
1
2
COMPRESSOR
9
2
J
8
6
4
3
5
7
1