Yamaha MGP32X Manual Do Utilizador
MGP32X/MGP24X Owner’s Manual
26
Using Effects (FX)
The MGP32X/MGP24X features two built-in effects;
FX1 and FX2. FX1 has REV-X reverb (8 types), while
FX2 has SPX multi effects (a total of 16 types, including
reverb, delay, echo). The effects give you a wide range
of tools to further enhance your mixes.
FX1 and FX2. FX1 has REV-X reverb (8 types), while
FX2 has SPX multi effects (a total of 16 types, including
reverb, delay, echo). The effects give you a wide range
of tools to further enhance your mixes.
Applying effects
1.
Press the FX1 (or FX2) button located below
the display repeatedly if necessary until the (1/
2) MAIN page appears.
the display repeatedly if necessary until the (1/
2) MAIN page appears.
2.
Rotate or press Knob 1 to display the program
list.
list.
NOTE
For details on effect programs, refer to the Appendix (page 43).
3.
Rotate Knob 1 to select the desired program,
and then press Knob 1 to actually call it up.
and then press Knob 1 to actually call it up.
The selected program will be called up.
4.
Turn on the ON switch of the input channel,
and then rotate the channel’s FX1 (or FX2)
knob to send the signal to FX1 RTN (or FX2
RTN).
and then rotate the channel’s FX1 (or FX2)
knob to send the signal to FX1 RTN (or FX2
RTN).
5.
Raise the input channel
fader to the “0” position.
fader to the “0” position.
6.
Turn on the ON switch of
the FX1 RTN (or FX2 RTN)
channel.
the FX1 RTN (or FX2 RTN)
channel.
7.
Raise the FX1 RTN (or FX2
RTN) fader to the “0” posi-
tion.
RTN) fader to the “0” posi-
tion.
8.
Rotate Knob 2 to adjust the effect depth.
The value on the lower right side of the screen will change on
the display.
the display.
NOTE
If 06 VOCAL ECHO, 07 KARAOKE ECHO, 08 DELAY, or 09
SINGLE DELAY is selected for the FX2 program, you can
adjust the Delay in finer units of 0.1ms by simultaneously hold-
ing down Knob 2 and rotating it. This function also applies to
the (2/2) PARAMETER page and the page that both FX1 and
FX2 screens are displayed on.
SINGLE DELAY is selected for the FX2 program, you can
adjust the Delay in finer units of 0.1ms by simultaneously hold-
ing down Knob 2 and rotating it. This function also applies to
the (2/2) PARAMETER page and the page that both FX1 and
FX2 screens are displayed on.
9.
Use the FX1 RTN (or FX2 RTN) fader to adjust
the overall effect depth.
the overall effect depth.
Detailed effect settings
1.
Press the FX1 (or FX2) button below the dis-
play repeatedly if necessary until the (2/2)
PARAMETER page appears.
play repeatedly if necessary until the (2/2)
PARAMETER page appears.
2.
Rotate Knob 1 to select the desired parameter,
and then rotate Knob 2 to set the value.
and then rotate Knob 2 to set the value.
FX1 lets you make the following parameter settings.
• Rev Time: Length of reverb time
• Diffusion: Right and left diffusions
• Ini Delay: Initial delay before reverb begins
• Room Size: Size of room
• Diffusion: Right and left diffusions
• Ini Delay: Initial delay before reverb begins
• Room Size: Size of room
NOTE
For FX2, the effect parameters depend on the effect type. For
details about each parameter, refer to the Appendix (pages 44-
45).
details about each parameter, refer to the Appendix (pages 44-
45).
Indicates MAIN page
Knob 2
Knob 1
Turn on
“0”
FX1