Yamaha 02R96 Manual Do Utilizador
MIDI Data Format
275
02R96—Owner’s Manual
MIDI Data Format
1. CHANNEL MESSAGE
2. SYSTEM COMMON MESSAGE
3. SYSTEM REALTIME MESSAGE
Received only when the Automix TIME REFERENCE setting is
MIDI CLOCK.
MIDI CLOCK.
4. EXCLUSIVE MESSAGE
4.1 Real Time System Exclusive
4.2 System Exclusive Message
4.2.1 Bulk Dump
The following data types of bulk dump are used on the 02R96.
4.2.2 PARAMETER CHANGE
The following data types of parameter change are used by the 02R96.
** tx means that the data can be transmitted from the 02R96. rx means that
the data can be received by the 02R96.
the data can be received by the 02R96.
Format Details
1. NOTE OFF (8n)
Reception
Received when the [Rx CH] matches.
Used to control effects.
Received when the [Rx CH] matches.
Used to control effects.
2. NOTE ON (9n)
Reception
Received when the [Rx CH] matches.
Used to control effects.
Received when the [Rx CH] matches.
Used to control effects.
3. CONTROL CHANGE (Bn)
Reception
Received when [Control Change Rx] is ON and the [Rx CH] matches.
However if [OMNI] is ON, this is received regardless of the channel. If
[Control Change ECHO] is ON, these messages are echoed to MIDI OUT.
If [TABLE] is selected, parameters will be controlled according to the set-
tings of the [Control assign table]. The parameters that can be set are de-
fined in the CONTROL CHANGE ASSIGN PARAMETER LIST. If
[NRPN] is selected, four messages are used to control the defined param-
eter: NRPN control numbers (62h, 63h) and DATA ENTRY control num-
bers (06h, 26h). Parameter settings are defined in the CONTROL
CHANGE ASSIGN PARAMETER LIST.
Received when [Control Change Rx] is ON and the [Rx CH] matches.
However if [OMNI] is ON, this is received regardless of the channel. If
[Control Change ECHO] is ON, these messages are echoed to MIDI OUT.
If [TABLE] is selected, parameters will be controlled according to the set-
tings of the [Control assign table]. The parameters that can be set are de-
fined in the CONTROL CHANGE ASSIGN PARAMETER LIST. If
[NRPN] is selected, four messages are used to control the defined param-
eter: NRPN control numbers (62h, 63h) and DATA ENTRY control num-
bers (06h, 26h). Parameter settings are defined in the CONTROL
CHANGE ASSIGN PARAMETER LIST.
Transmission
If [TABLE] is selected, operating the parameters specified in the [Control
assign table] will cause these messages to be transmitted on the [Tx CH] if
[Control Change TX] is ON. The parameters that can be specified are de-
fined in the CONTROL CHANGE ASSIGN PARAMETER LIST.
If [NRPN] is selected, operating the specified parameters will cause data to
be transmitted on the [Tx CH] if [Control Change TX] is ON, using four
messages: NRPN control numbers (62h, 63h) and DATA ENTRY control
numbers (06h, 26h). Parameter settings are defined in the CONTROL
CHANGE ASSIGN PARAMETER LIST.
If [TABLE] is selected, operating the parameters specified in the [Control
assign table] will cause these messages to be transmitted on the [Tx CH] if
[Control Change TX] is ON. The parameters that can be specified are de-
fined in the CONTROL CHANGE ASSIGN PARAMETER LIST.
If [NRPN] is selected, operating the specified parameters will cause data to
be transmitted on the [Tx CH] if [Control Change TX] is ON, using four
messages: NRPN control numbers (62h, 63h) and DATA ENTRY control
numbers (06h, 26h). Parameter settings are defined in the CONTROL
CHANGE ASSIGN PARAMETER LIST.
Command
rx/tx
function
8n NOTE OFF
rx
Control the internal effects
9n NOTE ON
rx
Control the internal effects
Bn CONTROL CHANGE
rx/tx
Control parameters
Cn PROGRAM CHANGE
rx/tx
Switch scene memories
Command
rx/tx
function
F1 MIDI TIME CODE QUARTER
FRAME
FRAME
rx
Used when TIME REFERENCE is
MIDI CLOCK.
MIDI CLOCK.
F2 SONG POSITION POINTER
rx
Used when TIME REFERENCE is
MIDI CLOCK.
MIDI CLOCK.
Command
rx/tx
function
F8 TIMING CLOCK
rx
MIDI clock
FA START
rx*
Start automix (from the
beginning)
beginning)
FB CONTINUE
rx*
Start automix (from the
middle)
middle)
FC STOP
rx*
Stop automix
FE ACTIVE SENSING
rx
Check MIDI cable connections
FF RESET
rx
Clear running status
Command
rx/tx
function
F0 7F dd 06 MMC COMMAND
tx
MMC command (refer to
MMC specification)
MMC specification)
F0 7F dd 07 MMC RESPONSE
rx
MMC response (refer to MMC
specification)
specification)
F0 7F dd 01 MIDI TIME CODE
rx
Used when TIME REFERENCE is
MTC.
MTC.
Command
rx/tx
function
F0 43 0n 7E BULK DUMP DATA
rx/tx
BULK DUMP DATA
F0 43 2n 7E BULK DUMP REQUEST
rx/tx
BULK DUMP REQUEST
Data name
tx/rx
function
'm'
tx/rx
Scene Memory & Request
'S'
tx/rx
Setup Memory & Request
'a'
tx/rx
Automix data & Request
'R'
tx/rx
Input patch library & Request
'O'
tx/rx
Output patch library & Request
'H'
tx/rx
Channel library & Request
'G'
tx/rx
Gate library & Request
'Y'
tx/rx
Compressor library & Request
'Q'
tx/rx
Equalizer library & Request
'E'
tx/rx
Effect library & Request
'J'
tx/rx
Bus to Stereo library & Request
'K'
tx/rx
Surround Monitor library & Request
'P'
tx/rx
Program change table & Request
'C'
tx/rx
Control change table & Request
'L'
tx/rx
User define layer & Request
'I'
tx/rx
Plug-in User define & Request
'V'
tx/rx
User define key & Request
'N'
tx/rx
Plug-in Effect Card Data & Request
Command
rx/tx
function
F0 43 1n 3E 0B PARAMETER
CHANGE
CHANGE
rx/tx
02R96-specific parameter
change
change
F0 43 3n 3E 0B PARAMETER
REQUEST
REQUEST
rx/tx
02R96-specific parameter
request
request
F0 43 1n 3E 7F PARAMETER
CHANGE
CHANGE
rx/tx
General purpose digital mixer
parameter change
parameter change
F0 43 3n 3E 7F PARAMETER
REQUEST
REQUEST
rx/tx
General purpose digital mixer
parameter request
parameter request
Type
tx/rx
function
1
tx/rx
Edit buffer
2
tx/rx
Patch data
3
tx/rx
Setup data
4
tx/rx
Backup data
16
tx/rx
Function (recall, store, title)
17
rx
Function (pair)
18
rx
Function (event)
32
rx
Key remote
33
tx/rx
remote meter
34
tx/rx
remote counter
STATUS
1000nnnn 8n
Note off message
DATA
0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (ignored)
STATUS
1001nnnn 9n
Note on message
DATA
0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (1-127:on, 0:off)