Yamaha EMX88s Manual Do Utilizador
12
Front and rear panel
EMX88S/EMX68S—Owner’s Manual
D
2TR IN control
This adjusts the amount of signal that is sent
from the 2TR IN jacks to the stereo (MAIN L, R)
bus.
from the 2TR IN jacks to the stereo (MAIN L, R)
bus.
E
MASTER control
This control adjusts the stereo (MAIN L, R) bus
signal output level.
signal output level.
This setting is output to the SPEAKERS A, B,
BRIDGE jacks and the MAIN (STEREO) jack
(input/output panel
BRIDGE jacks and the MAIN (STEREO) jack
(input/output panel
7
) on the rear panel and
appears in the stereo (MAIN L, R) bus signal.
F
Peak level indicator
This indicator allows you to monitor the level of
the signal which is output from the MAIN (STE-
REO) jack (input/output panel
the signal which is output from the MAIN (STE-
REO) jack (input/output panel
7
).
■ MONITOR section
This section allows you to adjust the tone and
volume of the MONITOR bus, and specify the
mix level of the built-in digital effect.
volume of the MONITOR bus, and specify the
mix level of the built-in digital effect.
G
Graphic equalizer
The EMX88S/EMX68S has a 7-band graphic
equalizer for adjusting the frequency response of
the MONITOR bus signal. This allows you to cut
or boost each frequency band by a maximum of
±12dB. You can use these sliders to reduce the
level of frequency bands at which feedback easily
occurs. Frequency response is flat when a slider is
in the center position. Moving a slider in the pos-
itive direction will boost, and in the negative
direction will cut.
The EMX88S/EMX68S has a 7-band graphic
equalizer for adjusting the frequency response of
the MONITOR bus signal. This allows you to cut
or boost each frequency band by a maximum of
±12dB. You can use these sliders to reduce the
level of frequency bands at which feedback easily
occurs. Frequency response is flat when a slider is
in the center position. Moving a slider in the pos-
itive direction will boost, and in the negative
direction will cut.
These graphic equalizer settings affect both the
MONITOR bus signal output to the speakers and
the line level signal sent from MONITOR jack
signal (input/output panel 7).
MONITOR bus signal output to the speakers and
the line level signal sent from MONITOR jack
signal (input/output panel 7).
H
EFFECT RTN control
This control adjusts the effect signal level sent to
the MONITOR bus from the built-in digital
effect.
This control adjusts the effect signal level sent to
the MONITOR bus from the built-in digital
effect.
I
2TR IN control
This control adjusts the amount of signal that is
sent from the 2TR IN jacks to the MONITOR
bus.
This control adjusts the amount of signal that is
sent from the 2TR IN jacks to the MONITOR
bus.
J
MASTER control
This control adjusts the MONITOR bus signal
output level.
This control adjusts the MONITOR bus signal
output level.
This setting is output to both the front and rear
panel MONITOR jacks and appears in the MON-
ITOR bus signal.
panel MONITOR jacks and appears in the MON-
ITOR bus signal.
K
Peak level indicator
This indicator allows you to monitor the level of
the signal which is output from the MONITOR
jack (input/output panel 7).
This indicator allows you to monitor the level of
the signal which is output from the MONITOR
jack (input/output panel 7).
■ PHANTOM switch, indicator
L
PHANTOM ON, OFF switch
This switch turns the phantom power supply on/
off for the Low-Z XLR type input jacks of chan-
nels 1–6 (EMX88S), 1–4 (EMX68S).
This switch turns the phantom power supply on/
off for the Low-Z XLR type input jacks of chan-
nels 1–6 (EMX88S), 1–4 (EMX68S).
Turn this switch off if you do not use it.
Note: To avoid distortion, adjust the MASTER
control (E) so that the 0 indicator lights occa-
sionally.
control (E) so that the 0 indicator lights occa-
sionally.
K
H
J
I
G
Note: To avoid distortion, adjust the MASTER
control (J) so that the 0 indicator lights occa-
sionally.
control (J) so that the 0 indicator lights occa-
sionally.
L