Siemens TC12 Manual Do Utilizador
TC12 Installation, Commissioning & Maintenance Handbook
Set the I/O Port addresses of the boards using DIP switch 1 (DS1) positions 9 to
11, as shown below:
11, as shown below:
Board
SW9
SW10
SW11
Address
1 ON
OFF
OFF
0x100
2 ON ON OFF
0x120
3 OFF
OFF ON 0x200
4 ON
OFF ON 0x220
Set the interrupts using DIP switch 2 (DS2), positions 1 to 8, as shown below:
Board SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
Interrupt
1
OFF OFF ON OFF OFF OFF OFF OFF IRQ5
2
OFF OFF OFF OFF OFF ON
OFF
OFF
IRQ11
3
OFF OFF OFF OFF OFF OFF OFF ON IRQ15
Q7
2.2.
he DIGI PC/16i comprises a full length ISA card (DIGI part number 60000200)
a
The PC board has a single jumper (J1) and 2 DIP switches (DS1 and DS2).
The jum
The jumper has 3 pins which are numbered from left to right. The jumper should
be set so that pins 2 and 3 are bridged.
The PC board has a single jumper (J1) and 2 DIP switches (DS1 and DS2).
The jum
The jumper has 3 pins which are numbered from left to right. The jumper should
be set so that pins 2 and 3 are bridged.
The setting of the2 DIP switches, DS1 and DS2, is the same as for the DIGI
2.2.
he DIGI AccelePort Xem comprises a three quarter length Xem ISA Host Adapter
(419/4/95931/000 - DIGI part number 77000211), a 16em DB25 Module
) and a Xem 5ft Cable
he
C
alled. The
PC should remain off until the 16em DB25 Modules have been connected to the
host adapter. The only set up required on the Xem host adapter is to set the I/O
por
host adapter. The only set up required on the Xem host adapter is to set the I/O
por
d
Addr
4
OFF OFF OFF ON OFF OFF OFF OFF IR
2.8.2 DIGI AccelePort 16e
T
nd an IMD Distribution Unit (labelled Digi AccelePort 16e ISA DB25M RS232).
per is used to set the local program memory size, which should be 64K.
2.8.3 DIGI AccelePort Xem
T
(653/4/05229/000 - DIGI part number 76000073
(707/4/08514/000 - DIGI part number 62080060). Each 16em DB25 Module is
supplied with a short cable which enables a maximum of 4 16em DB25 Modules to
be daisy chained together. Two 16em DB25 Modules may be powered from the
ISA Host Adapter. Additional Modules require auxiliary power supplies
(605/4/08678/000 - DIGI part number 76000321).
T
(707/4/08514/000 - DIGI part number 62080060). Each 16em DB25 Module is
supplied with a short cable which enables a maximum of 4 16em DB25 Modules to
be daisy chained together. Two 16em DB25 Modules may be powered from the
ISA Host Adapter. Additional Modules require auxiliary power supplies
(605/4/08678/000 - DIGI part number 76000321).
T
P must be powered off before the Xem host adapter card is inst
t a dress to 124H-127H using DIP switch DS1
ess
SW1
SW2
SW3
SW4
124H-127H
OFF ON ON ON
666/HE/43100/000
Page 17
Issue 9