Marshall Amplification MF350 Manual Do Utilizador
11
10
ENGLISH
ENGLISH
Cabinet Impedance
The MODE FOUR must be connected to a minimum load of 8
Ohms. Connecting a load of less than 8 Ohms and playing the amp
will trigger the LOAD PROTECTION (rear panel 6) and could damage
the Mode Four or the speaker cabinet.
will trigger the LOAD PROTECTION (rear panel 6) and could damage
the Mode Four or the speaker cabinet.
The recommended set-ups are shown below:
Note: these are the only impedance combinations allowed.
MF280 & MF400 4x12" Cabinets
Countless hours of Research and Development went in to the development of the MF350 and it
became clear at an early stage that special cabinets would be needed to get the most from it. The
MF280 (280W) and MF400 (400W) cabinets are the result of this parallel design process. Designed
specifically to reproduce the balanced mid range and huge bottom end that are a prerequisite for
extreme hard rock and nu-metal sounds, these cabinets feature:
MF280 (280W) and MF400 (400W) cabinets are the result of this parallel design process. Designed
specifically to reproduce the balanced mid range and huge bottom end that are a prerequisite for
extreme hard rock and nu-metal sounds, these cabinets feature:
■
Sonically optimised Celestion loudspeaker designs
■
Pro-gauge internal wiring
■
Increased internal volume
The ultra-rugged construction has been underpinned with literally hundreds of hours of extreme
endurance (soak) testing using real life signals in real life conditions. This has assured us that these
cabinets are not only ready for the sonic demands of a high performance head like the MF350, but
also the extreme physical abuse they may receive on the road.
cabinets are not only ready for the sonic demands of a high performance head like the MF350, but
also the extreme physical abuse they may receive on the road.
We recommend the MF280A (angled) and B (base) for full stack operation and the MF400A or B
for half stack operation.
8 Ohm Half Stack
16 Ohm Half Stack
Full Stack
8 Ohm
Min Power 350W
(e.g. MF400A or B)
16 Ohm
Min Power 235W
(e.g. MF280A or B)
16 Ohm
Min Power 235W
(e.g. MF280A)
16 Ohm
Min Power 235W
(e.g. MF280B)
Full Stack versus Half Stack
The MODE FOUR can be used either as a full stack (two cabinets) or half stack (one cabinet)
configuration. The rig you choose is a matter of personal taste and as always when it comes to
sound we recommend you try both to see which suits your style best. Below is a guide to the major
attributes of each:
sound we recommend you try both to see which suits your style best. Below is a guide to the major
attributes of each:
Full Stack:
Enhanced on stage spread.
More ‘cut through’ due to accentuated treble and high mids.
Iconic stage presence.
More ‘cut through’ due to accentuated treble and high mids.
Iconic stage presence.
Half Stack:
More controllable spread of sound on stage (especially base type)
Convenient and portable.
Convenient and portable.
Half Stack Options
If the full 350W is to be delivered using a single cabinet it must have an impedance of 8 Ohms.
Equally important is that the cabinet must have a nominal power rating of 350W or above if 8 Ohms,
or 235W or above if 16 Ohms.
or 235W or above if 16 Ohms.
The MF400A and MF400B are 8 Ohm/400W cabinets specifically voiced for use in half stack
configurations with the Mode Four.
Whether you choose an angled or base half stack configuration is a personal choice between the
different tonal qualities of each set up.
The MF400A (angled) is, in keeping with other angled 4x12" cabinets, tonally more aggressive
than the base option. The angled cabinet is the usual choice for those who want a more prominent
upper mid and treble response that really cuts through in a live situation.
upper mid and treble response that really cuts through in a live situation.
Alternatively, the MF400B (base) delivers a more even mid range with less spread of the
aggressive treble response. Marshall 4x12" base cabinets are more often used by professionals as
they have a more focused bottom end and a smoother mid range and treble response. They are
often easier to deal with in terms of sound reinforcement and monitoring in a live situation.
they have a more focused bottom end and a smoother mid range and treble response. They are
often easier to deal with in terms of sound reinforcement and monitoring in a live situation.
Rear Panel Connections
Shown below is the Loudspeaker Connection chart from the MF350 rear panel.
Half Stack Connection
SPEAKER OUTPUTS I and II are specifically designed to provide the optimum damping on 8 or
16 Ohm cabinets in half stack operation.
We recommend connection of a single 16 Ohm cabinet to SPEAKER OUTPUT I or connection of
a single 8 Ohm cabinet to SPEAKER OUTPUT II.
Full Stack Connection
Connect two 16 Ohm cabinets to SPEAKER OUTPUTS I and II.
OUTPUT
I
II
235W
16 Ω
X
350W
X
8 Ω
350W
16 Ω
16 Ω
MODE FOUR Cabinet Options