Mitsubishi Electronics A800 Manual Do Utilizador

When connecting the high power factor converter (FR-HC2) to suppress power harmonics, perform wiring securely as shown 
below. Incorrect connection will damage the high power factor converter and the inverter.
After making sure that the wiring is correct, set "rated motor voltage" in Pr.19 Rated motor voltage (under V/F control) or 
Pr.83 Regenerative function selection (under other that V/F control) and "2" in Pr.30 Regenerative function selection.

 • The voltage phases of terminals R/L1, S/L2, and T/L3 and the voltage phases of terminals R4/L14, S4/L24, and T4/L34 must 

be matched.

 • The control logic (sink logic/source logic) of the high power factor converter and the inverter must be matched. (Refer to 

 • When using a sine wave filter with FR-HC2, select MT-BSL-HC as a reactor for the sine wave filter.
 • For the parameter details, refer to the FR-A800 Instruction Manual (Detailed).



Remove jumpers installed in terminals R1/L11 and S1/L21 of the inverter, and connect the power supply for the control circuit to terminals 
R1/L11 and S1/L21.



The voltage phases of terminals R4/L14, S4/L24, and T4/L34 and the voltage phases of terminals R/L1, S/L2, and T/L3 must be matched. 



Do not install an MCCB across the terminals P/+ and N/- (across terminals P and P/+ or across N and N/-). Connecting the opposite polarity 
of terminals N/- and P/+ will damage the inverter.
For the A802 series, installation of a fuse is not required.



Change the FR-HC2 parameter setting to Pr.10 RDY signal logic selection = "0" (positive logic).



Use Pr.178 to Pr.189 (input terminal function selection) to assign the terminals used for the X10 signal.
For RS-485 or any other communication where the start command is only transmitted once, use the X11 signal to save the operation mode 
at the time of an instantaneous power failure.



Assign the IPF signal to an FR-HC2 terminal. (Refer to the Instruction Manual of FR-HC2.)



Always connect the FR-HC2 terminal RDY to the inverter terminal MRS(X10), and the FR-HC2 terminal SE to the inverter terminal SD. Not 
connecting these terminals may damage the FR-HC2.



Always connect the R/L1, S/L2, and T/L3 terminals of FR-HC2 to the power supply. Operating the inverter without connecting them will 
damage the FR-HC2.



Do not install an MCCB or MC between the reactor 1 terminals (R/L1, S/L2, T/L3) and the FR-HC2 terminals (R4/L14, S4/L24, T4/L34). It 
will not operate properly.

 Securely perform grounding (earthing) by using the grounding (earthing) terminal.
 The number of connected peripheral devices differs according to the capacity. For the detail, refer to the FR-HC2 Instruction Manual.

MC1

MC2

MC3

M

R1/L11
S1/L21

R4/L14

S4/L24

T4/L34

R4/

L14

S4/

L24

T4/

L34

R3/
L13

S3/
L23

T3/
L33

R2/

L12

S2/

L22

T2/

L32

R/
L1

S/
L2

T/
L3

MC

U
V

W

88R

R/L1
S/L2
T/L3

88S

R1/L11
S1/L21

MC
Bu1

MC1

MC2

MC3

ROH

SD

MC2 MC3

MC

Small

MC

Bu2

MC1

P/+

P/+

N/-

N/-

X11

RES

SD

IPF

RSO

SE

∗11

∗11

∗11

∗9

∗9

∗9

∗10

∗5

∗4

∗6

X10

RDY

∗7

∗7

∗1

∗10

∗8

∗3

∗2

Inverter

High power

factor converter

(FR-HC2)

Limit resistor

Reactor 1

(FR-HCL21)

Power 
Supply

MCCB

Reactor 2

(FR-HCL22)

Earth
(Ground)

Limit MC

Buffer relay for driving MCs

MC power 

supply 

stepdown

transformer

Mini relay for filter 
capacitor alarm detector

Buffer relay for 

filter capacitor 

alarm detectors

Auxiliary contact for 
limit MCs (NO contact)   3

Filter capacitor 
alarm detector 
(NC contact)   2

Limit resistor (with thermostat) 

(NC contact)   3

Filter capacitors   2

(FR-HCC2)