Anton/Bauer ElipZ 10K Folheto
The power behind the best cameras capturing the best images in the world.
sm
TM
FULLY READ ALL INSTRUCTIONS BEFORE USE
ATTACH BATTERY TO CAMERA
(1) Charge battery fully (see “CHARGING” section)
(2) Remove shoe mount from battery
(3) Attach shoe to bottom of camera – tighten securely
(4) Pull back on battery slide lock
(5) Attach battery to shoe mount on bottom of camera, release slide lock
(6) Connect faux battery end of camera cable to camera battery connection
(7) Connect ELIPZ connector end of camera cable to ELIPZ 10k battery
(3) Attach shoe to bottom of camera – tighten securely
(4) Pull back on battery slide lock
(5) Attach battery to shoe mount on bottom of camera, release slide lock
(6) Connect faux battery end of camera cable to camera battery connection
(7) Connect ELIPZ connector end of camera cable to ELIPZ 10k battery
OPERATION OF BATTERY
The “blue” LED (battery at >7.2V)
generally indicates that the battery has
sufficient power to operate. The “yellow” LED (battery
<7.2V) generally indicates that the battery should be re-
charged before using. If neither LED is lit, the battery
should be placed on the charger and allowed to remain
there until the charger indicates a steady “green” LED.
IMPORTANT: Discharging the ELIPZ battery at loads
greater than 6 amps (approx. 42 watts) will decrease the
service life of the battery and will cause the internal battery
fuse to trip causing an interruption of power. If the battery
fuse opens due to excessive power drawn from the
battery, the battery fuse will automatically reset within a
few minutes after the load has been removed.
generally indicates that the battery has
sufficient power to operate. The “yellow” LED (battery
<7.2V) generally indicates that the battery should be re-
charged before using. If neither LED is lit, the battery
should be placed on the charger and allowed to remain
there until the charger indicates a steady “green” LED.
IMPORTANT: Discharging the ELIPZ battery at loads
greater than 6 amps (approx. 42 watts) will decrease the
service life of the battery and will cause the internal battery
fuse to trip causing an interruption of power. If the battery
fuse opens due to excessive power drawn from the
battery, the battery fuse will automatically reset within a
few minutes after the load has been removed.
TRANSPORTATION NOTICE – lithium ion battery pack
The ELIPZ 10k battery is suitable for air travel as a non-hazardous article under the regulations of the International Air Transport
Association (IATA), the International Civil Aviation Organization (ICAO) and the United Nations (UN). The ELIPZ 10k battery
pack contains aggregate lithium equivalence not exceeding 8 grams. This quantity is in compliance with Section A45-2* of the
Hazardous Substance Standards of the IATA and ICAO and is thus suitable for air transport as a non-hazardous article.
Association (IATA), the International Civil Aviation Organization (ICAO) and the United Nations (UN). The ELIPZ 10k battery
pack contains aggregate lithium equivalence not exceeding 8 grams. This quantity is in compliance with Section A45-2* of the
Hazardous Substance Standards of the IATA and ICAO and is thus suitable for air transport as a non-hazardous article.
®
T
he worldwide standard
®
ELIPZ Battery specifications
Electrical:
Nominal
Nominal
Capacity:
10,500
mAH
Nominal Voltage:
7.2 Volts
Nominal Charging Time (with ELIPZ charger):
6-7 Hours
Rated Maximum Discharge Current:
6 Amperes
End of Discharge Voltage:
5.4 Volt
Environmental:
Operating
Operating
Temperature
Range:
Charging:
10ºC
to
40ºC
Discharging:
-20ºC
to
60ºC
Storage Temperature Range:
Less than one month:
-30ºC to 30ºC
Recommended long term storage temp:
10ºC
Physical:
Dimensions: 6.43 x 3.17 x 1.70 inches (16.3 x 8.0 x 4.3 cm)
Weight:
Approx.
1.25
lbs
(567
grams)