Genesis Advanced Technologies GMSUDR15L Manual Do Utilizador
a b c
FIG 21
FIG 22
FIG 23
d
English
10" Slide Compound Laser Miter Saw
Operator’s Manual
GMSUDR15L
MAinTEnAnCE
SAW BLADE INSTALLATION OR REMOVAL
WArning:
Be sure that the tool is switched off and unplugged from the power source before performing any
work on the tool.
WArning:
Use only 10” diameter saw blades that have 5/8” diameter arbor holes and are rated for speeds
equal to or greater then the nameplate rated rPM of this miter saw.
WArning:
Use only blades designed for cross-cutting operations.
WArning:
Do not use thin kerf blades with deep gullets which may deflect and contact the blade guards or
produce poor quality cuts in the work piece.
To remove the blade
1. Unplug the tool from the power source.
2. Unlock and move the saw arm fully upright.
3. Using a Phillips screwdriver loosen and remove the screw (b) that secures the guard retraction arm. (FIG 21)
4. Using a Phillips screwdriver loosen and remove the lower screw (a) that secures the blade cover.
5. Using a Phillips screwdriver loosen the upper screw (c), no need to remove this screw.
6. Rotate the guard upwards and back exposing the saw blade arbor nut. (FIG 22)
7. Depress the rectangular spindle lock button (d) below the carrying handle and rotate the blade until it is locked in place by the spindle lock. you will
2. Unlock and move the saw arm fully upright.
3. Using a Phillips screwdriver loosen and remove the screw (b) that secures the guard retraction arm. (FIG 21)
4. Using a Phillips screwdriver loosen and remove the lower screw (a) that secures the blade cover.
5. Using a Phillips screwdriver loosen the upper screw (c), no need to remove this screw.
6. Rotate the guard upwards and back exposing the saw blade arbor nut. (FIG 22)
7. Depress the rectangular spindle lock button (d) below the carrying handle and rotate the blade until it is locked in place by the spindle lock. you will
find it easier if you reach around the motor housing from the front with your right hand to depress the Spindle Lock Button (d). (FIG 23)
8. Maintain pressure on the spindle lock with your right hand. Using your left hand and the supplied allen wrench , rotate the blade’s locking bolt,
clockwise to loosen, and then remove the blade’s locking bolt, small washer and outer blade flange washer; then remove the blade from the motor
spindle.
spindle.
To install the blade
1. Mount the blade carefully onto the spindle, being sure that the directional arrow on the blade surface matches the arrow on the upper blade guard.
2. Install the outer flange, small flat washer and hex bolt and turn the hex bolt finger tight in a counterclockwise direction.
3. Depress and hold down the spindle lock while tightening the blade locking bolt securely with the provided wrench in a counterclockwise direction.
4. Rotate the guard and center cover section to their original positions.
5. Align and then retighten the screws securing the lower saw guard assembly.
6. Test the lower guard operation by lowering the handle, being sure the guard retracts and then returns to the upright position properly.
7. Be sure the spindle lock has released and blade rotates freely before plugging in the tool and making a cut.
2. Install the outer flange, small flat washer and hex bolt and turn the hex bolt finger tight in a counterclockwise direction.
3. Depress and hold down the spindle lock while tightening the blade locking bolt securely with the provided wrench in a counterclockwise direction.
4. Rotate the guard and center cover section to their original positions.
5. Align and then retighten the screws securing the lower saw guard assembly.
6. Test the lower guard operation by lowering the handle, being sure the guard retracts and then returns to the upright position properly.
7. Be sure the spindle lock has released and blade rotates freely before plugging in the tool and making a cut.
WArning:
Whenever installing a new blade, always be sure that the new blade does not contact any part of the
machine’s metal base when the handle is completely lowered. Perform this test with the tool unplugged from the power
source.
source.
CLEANING
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be
damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WArning:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come
in contact with plastic parts. Chemicals can damage, weaken ordestroy plastic which may result in
serious personal injury.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure
because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this
tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using
compressed air.
serious personal injury.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure
because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this
tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using
compressed air.