Genesis Advanced Technologies GMSUDR15L Manual Do Utilizador
English
10" Slide Compound Laser Miter Saw
Operator’s Manual
GMSUDR15L
WArning:
rEAD AnD UnDErSTAnD ALL WArningS, CAUTiOnS AnD OPErATing inSTrUCTiOnS BEFOrE USing THiS
EQUiPMEnT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious
personal injury.
EQUiPMEnT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious
personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY:
•
Keep your work area clean and well lit
. Cluttered benches and dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres
, such as in the presence of flammable liquids, gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
•
Keep bystanders, children, and visitors away while operating a power tool
. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
•
Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any adapter plugs in any earthed
(grounded) power tools. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and
grounded power supply system.
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and
grounded power supply system.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is grounded.
• Do not abuse the cord.
Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat. Oil, sharp
edges or moving parts. Damaged cords increase the risk of electric shock.
• When operating a power tools outside, use an extension cord suitable for outdoor use.
These cords are
rated for outdoor use and reduce the risk of electric shock.
• Do not use AC only rated tools with a DC power supply.
While the tool may appear to work. The electrical components
of the AC rated tool are likely to fail and rate a hazard to the operator.
PERSONAL SAFETY
•
Stay alert,
watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury
• Use safety equipment.
Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection for appropriate conditions will reduce personal injuries.
• Dress properly.
Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts. Air vents may cover moving parts and should be avoided.
• Avoid accidental starting.
Ensure the switch is in the off position before plugging in. Carrying power tool with your finger on the
switch or plugging in power tools that have the switch on invites accidents.
• Remove any adjusting keys or wrenches before turning the power tool on.
A wrench or key that is left
attached to a rotating part of the tool may result in personal injury.
• Do not overreach.
Maintaining proper footing and balance at all times. Loss of balance can cause an injury in unexpected situation
.
• If devices are provided for connection of dust extraction and collection facilities, ensure these are
connected and properly used.
Use of these devices can reduce dust related hazards.
• Do not use a ladder or unstable support.
Stable footing on a solid surface enables better control of the tool in unexpected
situations.
• Keep tool handles dry, clean and free from oil and grease.
Slippery handles cannot safely control the tool.
TOOL USE AND CARE
•
Secure the work piece.
Use clamp or other practical way to hold the work piece to a stable platform. Holding the work piece by hand
or against your body is unstable and may lead to loss of control.