Franklin AnyBook Reader Folheto

Your product is powered by 2 AAA batteries (not included). To install batteries:

Be sure the battery is installed correctly. Wrong polarity 

may damage the unit. For battery precautions, read overleaf.

Replace the batteries when:
•  The green LED light flashes quickly;
•  Playback can only be at minimum volume level, and;
•  Recording cannot be made.

3. Press     (Volume Up/Recording) or   (Volume Down) to adjust the volume.

•  Four options are available and can be selected in the below sequence.

 

(Normal) 

 Pitch up 

 Pitch down 

 Echo 

 Robot 

•  If you press

 without playing a recording, you hear beep sounds indicating a 

change of the voice effects mode. The number of beep sounds indicates the option 

you have selected. For example, two beep sounds indicate “Pitch up” is selected.   

You can make two types of recording: normal or special. Special recording allows voice 

morphing during playback by pressing 

 while normal recording does not allow voice 

changes. Please decide which recording to make before doing so.

•  Red LED light is on in the recording mode.

4.  Touch the sticker with the optical reader of the device.
•  For an inactivated Type 2 sticker, you hear a special sound prompt. 
•  For an activated Type 2 sticker already with your own recording, you hear 

your recording which will be replaced with the new one you are going 

to make.

•  For a non-recordable Type 1 sticker, you hear an error sound prompt

indicating the recording cannot be replaced. 

5.  For normal recording: Press and hold     (Volume Up/Normal 

Recording).

•  For special recording: Press and hold 

 (Voice Morphing/Special Recording).

 

6.  Start your recording after hearing four beep sounds.
•  You need to press and hold     (normal recording) or 

 (special 

recording) during the whole recording process. 

•  Red LED light flashes during recording.

 (special recording) to stop recording.

•  To ensure that your complete recording is stored, release     or 

 one 

  second after you finish your recording. 
•  A beep sound can be heard when recording stops. 
•  Red LED light is on. 

•  Green LED light is on.

The reader allows around 200 hours of recording. New recordings cannot be made when 

the memory of the device is full (You hear a beep sound immediately after the four-beep 

countdown). Please delete unwanted recordings from the activated Type 2 stickers. 

•  Red LED light is on in the recording mode.

4.  Press and hold     (Volume Up/Normal Recording) and   (Volume Down). 
•  Deletion starts when LED light flashes. You need to press and hold     

and   during the whole deletion process.  

•  For a non-recordable Type 1 sticker, you hear an error sound prompt

indicating the recording cannot be deleted. 

5. Release     and   when you hear a beep sound.
•  Deletion is completed.
•  Red LED light is on. 

•  Green LED light is on.

1. Press   (Power) to switch on the device.
•  You hear a sound prompt during switch on. 
•  Green LED light is on.

2. Press   to switch off the device. 
•  You hear a sound prompt during switch off. 
•  Green LED light is off.

The device will switch off automatically 

without operations for 4 minutes. You can 

hear special sound prompts at the second, 

third and fourth minute after inactivation. 

To hear samples of the sound prompts, 

touch the clocks below with your reader. 

This product includes three types of stickers.
Type 1: NON-RECORDABLE STICKERS
Three sets of special 

stickers with pre-

recorded sounds which 

cannot be replaced or 

deleted. 

Type 2: INACTIVATED STICKERS
Several sets of clear 

and white stickers for 

your own recordings 

which can be replaced 

or deleted anytime as 

you want.

Speaker
LED Light
Microphone

Power 

Volume Down 

Optical Reader

Volume Up   / 

Normal Recording 

Headphone Jack

Voice Morphing/ 

Special Recording

Lanyard Hole
(back side)

IMPORTANT: DO NOT write on the stickers 

and DO NOT put the clear stickers on dark 

surfaces or surfaces with patterns (light and 

plain surfaces are preferred). Otherwise, 

recordings may not play back.

In general, the stickers can be easily 

removed from and re-adhered on most 

kinds of paper except when the paper 

is too thin, made of special materials or 

with special coatings. When in doubt, 

please try to adhere and remove a sticker 

to test its adhesiveness before using the 

stickers extensively on a publication. 

When additional stickers are required, 

you can purchase them at www.

anybookreader.com.

Type 3: COMMAND STICKERS
A set of command 

stickers as shortcuts for 

making and deleting 

recordings. Please see 

the Quick Start Guide 

for instructions.

This product uses sound prompts to assist operations. For your familiarization of these 

sounds, touch the music note icons with your reader while reading the instructions to 

hear the sound prompt samples.  We recommend you read and “hear” through this user’s 

guide before making any recordings.  

TIPS: To ease the process in making and deleting recordings, use the provided 

command stickers as shortcuts. Read the Quick Start Guide for instructions. 

You may also make recordings and download to AnyBook Reader using the AnyBook 

Case software program. Read the Software Guide for details.

USB Port

(For connection with 

computer. See “Software 

Guide” for details)