Yamaha DSP5D Manual Do Utilizador
SCENE function
184
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual
Reference section
When using Recall Safe, parameters of which only one
instance for every two adjacent odd-numbered/even-num-
bered channels/modules will be handled as follows if only
one of the channels/modules is set to Recall Safe.
instance for every two adjacent odd-numbered/even-num-
bered channels/modules will be handled as follows if only
one of the channels/modules is set to Recall Safe.
• PAIR
The setting will be forcibly turned off (pairing will be
disabled).
disabled).
• GATE STEREO LINK
• COMP STEREO LINK
• GEQ LINK
• COMP STEREO LINK
• GEQ LINK
The LINK parameter will be forcibly turned off (link-
ing will be disabled).
ing will be disabled).
• DELAY GANG
• ATT GANG
• ATT GANG
The GANG parameter will be recalled. If GANG is
turned on because of the recall, operation will main-
tain the difference in the DELAY/ATT parameter
values following the recall.
turned on because of the recall, operation will main-
tain the difference in the DELAY/ATT parameter
values following the recall.
• MS DECODE
• FIXED/VARI
• FIXED/VARI
These parameters will not be recalled.
• PAN MODE
The PAN MODE parameter will be recalled. However
if the PAN MODE would be changed by the recall from
BALANCE to any other setting, or if it would be
changed to BALANCE from any other setting, the PAN
MODE and PAN parameters will not be recalled. If the
recall causes PAN MODE to be set to GANG PAN, the
difference in PAN parameter values will be maintained
for operation following the recall.
if the PAN MODE would be changed by the recall from
BALANCE to any other setting, or if it would be
changed to BALANCE from any other setting, the PAN
MODE and PAN parameters will not be recalled. If the
recall causes PAN MODE to be set to GANG PAN, the
difference in PAN parameter values will be maintained
for operation following the recall.
Hint
• Selective Recall applies when a scene is recalled in PRE-
VIEW mode.
• When you recall a scene, there may be cases in which a
conflict in pairing settings between Recall Safe and Selec-
tive Recall causes the settings of a parameter to differ
between L and R channels. In such cases, the parameter
will be linked when it is next operated.
tive Recall causes the settings of a parameter to differ
between L and R channels. In such cases, the parameter
will be linked when it is next operated.
Here you can specify how fader and pan will change
smoothly to their new values over a specified duration
when the scene is recalled.
smoothly to their new values over a specified duration
when the scene is recalled.
A FADING ENABLED/DISABLED
Enables/disables the Fade function for fader levels.
Note
• The settings in the FADE TIME screen are independent for
each scene. If you edit these settings, you must store that
scene in order to make your changes effective.
scene in order to make your changes effective.
• The Fade function will apply when you recall a scene for
which the ENABLED button is selected.
B INPUT CH PANNING ENABLED/DISABLED
(Input channel panning enable/disable)
If the ENABLED button is selected, the Fade function
will also apply to the PAN (BALANCE) parameter of
input channels. This button is independent from the
FADING ENABLED/DISABLED (
will also apply to the PAN (BALANCE) parameter of
input channels. This button is independent from the
FADING ENABLED/DISABLED (
1
) setting. Use the
following two buttons to select the input channels to
which this will apply.
which this will apply.
• When the ALL INPUT button is on
The Fade function will apply to the PAN (BALANCE)
parameter of all input channels.
parameter of all input channels.
• When the SAME AS FADING button is on
The Fade function will apply to the PAN (BALANCE)
parameter of only the input channels you select in
parameter of only the input channels you select in
4
.
C FADE TIME/START OFFSET
Use the following two buttons to select the parameters
that can be viewed/edited in the FADE TIME screen.
The indication at the right shows which button is cur-
rently selected.
that can be viewed/edited in the FADE TIME screen.
The indication at the right shows which button is cur-
rently selected.
• When the FADE TIME button is on
Edit the time (fade time) over which the fader or pan
parameter of the corresponding channel will reach the
new value when you recall a scene for which the Fade
function is enabled.
parameter of the corresponding channel will reach the
new value when you recall a scene for which the Fade
function is enabled.
FADE TIME screen
FADE TIME
1
2
3