Yamaha DSP5D Manual Do Utilizador
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual
Operating section
69
7
Using the Selected Channel section
J COMP [GAIN] encoder
Specifies the gain of the signal that has passed through
the compressor.
the compressor.
Here you can edit high pass filter parameters for the
selected channel. This section is available only if an input
channel is selected.
selected channel. This section is available only if an input
channel is selected.
A HPF [FREQUENCY] encoder
Specifies the cutoff frequency of the high pass filter.
B HPF [FREQUENCY] indicator
Indicates the currently specified high pass filter cutoff
frequency, in units of Hz.
frequency, in units of Hz.
C HPF [ON] key
Switches the high pass filter on/off.
Here you can edit equalizer parameters for the selected
channel. The equalizer structure differs as follows between
input channels and output channels.
channel. The equalizer structure differs as follows between
input channels and output channels.
❏ Input channels
You can use a four-band peak/dip type EQ (HIGH, HIGH
MID, LOW MID, LOW). The HIGH band can be switched
to an LPF or shelving type; the LOW band can be switched
to a shelving type.
MID, LOW MID, LOW). The HIGH band can be switched
to an LPF or shelving type; the LOW band can be switched
to a shelving type.
❏ Output channels
If a MIX channel or STEREO A/B is selected, you can use
an eight-band peak/dip type EQ. (Operation is divided into
UPPER and LOWER groups of four bands each.) For
MATRIX channels, you can use a four-band peak/dip type
EQ.
For any output channel, the HIGH band can be switched
to shelving or LPF. The LOW band can be switched to
shelving or HPF. For MIX channels and STEREO A/B
channels, this can be specified for UPPER and LOWER,
allowing you to apply shelving or filtering twice.
an eight-band peak/dip type EQ. (Operation is divided into
UPPER and LOWER groups of four bands each.) For
MATRIX channels, you can use a four-band peak/dip type
EQ.
For any output channel, the HIGH band can be switched
to shelving or LPF. The LOW band can be switched to
shelving or HPF. For MIX channels and STEREO A/B
channels, this can be specified for UPPER and LOWER,
allowing you to apply shelving or filtering twice.
Hint
• Input channels also provide an HPF that is independent of
the four-band EQ.
• Output channels do not have an independent HPF, but
instead allow you to switch the LOW band type to HPF.
• Switching the equalizer type to HPF or LPF can be done in
the EQ PARAM screen (
➥ p.250)
A EQ [ON] key
Switches the equalizer on/off for the selected channel.
B EQ [UPPER] key
C EQ [LOWER] key
C EQ [LOWER] key
If a MIX channel or STEREO A/B channel is selected,
these keys select the four-band group (UPPER or
LOWER) that you will edit. (The LED of the currently
selected key will light.)
If any other channel is selected, the LEDs of both keys
will be dark.
these keys select the four-band group (UPPER or
LOWER) that you will edit. (The LED of the currently
selected key will light.)
If any other channel is selected, the LEDs of both keys
will be dark.
Hint
By simultaneously holding down the EQ [UPPER] key and EQ
[LOWER] key, you can return the EQ GAIN settings of the
selected channel to a flat state.
[LOWER] key, you can return the EQ GAIN settings of the
selected channel to a flat state.
D EQ [
] key
If this key is on, the corresponding HIGH band EQ
type will be switched to shelving. In this case, the
HIGH band EQ [Q] knob will have no function.
type will be switched to shelving. In this case, the
HIGH band EQ [Q] knob will have no function.
HPF (High Pass Filter)
1
3
2
EQUALIZER
2
1
3
9
8
7
45
6