JVC DT-V9L5 Manual Do Utilizador

42

42

This monitor has two external control terminals.

●

  MAKE/TRIGGER terminal (RJ-45): The following external control 

systems are available.

(1)  MAKE (make contact) system:
 

Controls the monitor by short-circuiting the corresponding pin 
terminal to the GND pin terminal, or disconnecting (opening) it.

(2)  TRIGGER (trigger) system: 
 

Controls the monitor by sending the pulse signal instantaneously 
to the corresponding pin terminal.

  ☞ “Using the MAKE/TRIGGER system”on the right

●

  RS-232C terminal (D-sub 9-pin): Controls the monitor with the 

RS-232C system. (

☞ “Using the serial communication” on page 43)

Set the following items of “Remote Setting” in Set-Up Menu 
according to the external control terminal and control system. (

☞ 

“Parallel Type” on page 38)

Make

Trigger

—

*

1

  For a monitor connected to a personal computer etc, select the 

terminal the equipment is actually connected to.

“MAKE” takes precedence over other controls.

●

  You can use external control even when “Control Lock” is set to 

“Volume Lock” or “All Lock”. (

☞ page 39)

●

  When the monitor is off (on standby), external control is not 

available. But certain external controls (starting/terminating 
communication, turning on the monitor) are available through the 
serial communication. (

☞ page 44)

<MAKE/TRIGGER system>
You can control the monitor by a personal computer or dedicated 
controller*

2

.

●

  “Using the MAKE/TRIGGER system” on the right.

*

2

  The controller is not commercially available. Consult your dealer if 

you need it.

●

  For the details, see page 43.

PC, etc.

The MAKE/TRIGGER terminal is configured as follows. You can assign 
a function to each pin terminal in “Remote Setting”. (

☞ “Pin1, Pin2, 

Pin3, Pin4, Pin5” in “Parallel Type” on page 38)

●

  You cannot change the functions assigned to the pin terminals 

from 6th to 8th.

1

Pin1

2

Pin2

3

Pin3

4

Pin4

5

Pin5

This is a female terminal.

6

Tally*

1

7

Enable*

2

8

GND

*

1

  The 6th pin terminal controls turning on or off the tally lamp 

(available to control even when the 7th pin terminal is invalid).

*

2

  The 7th pin terminal makes the external control valid/invalid. Keep 

the 7th pin short-circuited to 8th pin to make the external control 
valid

For the operation procedure, see page 31.

1 

Select “Remote Setting” on the Set-Up Menu.

2 

Set “Parallel Type” to “Set.”

3 

Select a pin name (“Pin1” – “Pin5”) for which you want to assign a 
function, then select the function you want to assign.

 

For the selectable functions, see the table on page 43.

1 

Set “Parallel Type” of “Remote Setting” to “Make” or “Trigger” in the 
Set-Up Menu.

2 

Keep the 7th pin terminal (Enable) short-circuited to the 8th pin 
terminal (GND) so that the monitor can be controlled by the external 
control.

3 

When the “MAKE” system is selected: Operate each function by short-
circuiting the corresponding pin terminal to the 8th pin terminal 
(GND) or opening it.

 

When the “TRIGGER” system is selected: Operate each function by 
pulse control, that is short-circuiting the corresponding pin terminal 
to the 8th pin terminal (GND) for about 1 second and opening it.

●

  When changing the input with MAKE system, activate the pin you 

want after deactivating the currently used pin.

●

  When selecting the “TRIGGER” system, you can operate only one 

function at a time. Operate the functions one by one.

RS-232C

DT-F9L5_EU.indb   42

DT-F9L5_EU.indb   42

2012/12/18   14:13:08

2012/12/18   14:13:08