Sanyo CE52SR2 Manual Do Utilizador

Language is used to select the preferred language . Use the 1 or 
2 button to select English, French, German, Italian, Spanish or 
Dutch .
H-Position changes the OSD position horizontally by using the 1 
or 2 

button .

V-Position changes the OSD position vertically by using the 1 or 
2 button .
Duration is used to set the display time of the MENU by using the 
1 or 2 button . (5 ~ 120 seconds)
Transparence is used to adjust transparence of menu display . Use 
the 1 or 2 

button to adjust levels .

n

Use the 5 or 6 

button to select PIP/POP Setup and press the 

1 or 2 button to enter the sub menu .

PIP/POP Mode: Using the 1 or 2 button select the most suit-
able mode 

PIP1, PIP2, POP or Off . (Please refer to page 13 .)

✐

  When Mode is set to 

Off, Sub Source and PIP Position will not 

work . 

Main Source is used to select input source (AV1, RGB, AV2, AV3, PC, 
DVI or Network ) for main picture by using the 1 or 2 

button .

Sub Source is used to select input source (AV1, AV2, AV3, PC or 
DVI) for sub picture by using the 1 or 2 

button .

✐

  For a combination of main picture and sub picture: only DVI or 

Network input can assemble with other input source . For example, 
if main source is selected as AV1 input, then the sub source must 
be DVI or Network input .

PIP Position: Using the 1 or 2 button it can be selected Top 
Left, Top Right, Bottom Right or Bottom Left .

n

This function returns all setting values 

except for Installation Mode . 

n

Use the 5 or 6 

button to select Text Language and press the 

1 or 2 button to select Western, Eastern, Russian, Arabic or 
Farsi .

n

This function allows you to split an image to suit your monitor grid 
format to create a video wall .
Use the 5 or 6 button to select 

Tile Mode and press the 1 or 

2 button to enter the sub menu as follows .
Tile Mode Active can be set On or Off using the 1 or 2 button .

H_Sets is used to divide the horizonal picture into more than one 
part, but the most is 5 parts (5 monitors) .

V_Sets is used to divide the vertical picture into more than one part, 
and the most is also 5 parts (5 monitors) . Using the 1 or 2 
button to set .
H Location is used to select one part of the horizonal picture to dis-
play on the current LCD Monitor using the 1 or 2 

button .

V Location is used to select one part of the vertical picture to display 
on the current LCD Monitor using the 1 or 2 

button .

Bezel H Adjustment is used to align the image horizontally with re-
spect to the other monitors in the video wall to accomodate the bezel 
width using the 1 or 2 

button . (0 ~ 10) 

Bezel V Adjustment is used to align the image vertically with respect 
to the other monitors in the video wall to accomodate the bezel width 
using the 1 or 2 

button . (0 ~ 10)

n

Use the 5 or 6 

button to select AV2 Setting and press the 1 

or 2 

button to select YPbPr or RGBHV .

Connect your PC to either PC-IN or RGBHV on the rear of the set . 
Once connected select PC mode or AV2 (RGBHV, see page 5 for AV2 
input settings) via the 

INPUT button on your remote control .

The set will become a monitor for the PC .

n

Use the 5 or 6 

button to select Native Resolution and press the 

1 or 2 button to select XGA or WXGA 1366 x 768 .

n

The monitor set automatically turns off with no PC input signal and 
wakes up with signal while PC Power Save is active .
Use the 5 or 6 

button to select PC Power Save and press the 

1 or 2 button to select ON or OFF .

Press the 

MENU button and select PC Adj. using the 5 or 6 but-

tons, press the 1 or 2 button to enter . Press the BACK button 
to return to the previous menu . Press the 

MENU button to exit menu 

operation .

Auto Adjust is used to automatically detect incoming signal, and 
adjust itself to optimize its performance by using the 1 or 2 
button . If the image is not displayed properly, a manual adjustment is 
required (Refer to following adjustments) .
H-Position is used to move the horizontal picture position by using 
the 1 or 2 

button .

V-Position is used to move the vertical picture position by using the 
1 or 2 button .
Clock is used to eliminate flicker from the image by using the 1 or 
2 button .
Phase is used to eliminate disorder from the image by using the 1 
or 2 

button .