Lucent Technologies R5SI Manual Do Utilizador
DEFINITY Enterprise Communications Server Release 5
Maintenance and Test for R5vs/si
Maintenance and Test for R5vs/si
555-230-123
Issue 1
April 1997
Maintenance Object Repair Procedures
Page 10-528
DS1-BD (DS1 Interface Circuit Pack)
10
DS1-BD (DS1 Interface Circuit Pack)
The DS1 Interface circuit pack provides an interface to an external DS1 facility
and supports 24 DS0 channels carried on a 1.544 Mbps DS1 link. These DS0
channels can be administered as either trunks to other switches or lines to
off-premises stations. The TN464C and later suffix Universal DS1 Interface also
supports a 32-channel interface on a 2.048Mbps link. The functions and
maintenance strategy for the TN464 circuit packs are covered under a separate
maintenance object, UDS1-BD.
and supports 24 DS0 channels carried on a 1.544 Mbps DS1 link. These DS0
channels can be administered as either trunks to other switches or lines to
off-premises stations. The TN464C and later suffix Universal DS1 Interface also
supports a 32-channel interface on a 2.048Mbps link. The functions and
maintenance strategy for the TN464 circuit packs are covered under a separate
maintenance object, UDS1-BD.
DS1-BD maintenance logs in-line errors reported by the DS1 Interface circuit
pack, runs tests for error diagnosis and recovery, and raises and clears alarms.
The following table shows the capabilities of each DS1 circuit pack. The TN722
and TN722B are not supported on G3r V1 or later systems.
pack, runs tests for error diagnosis and recovery, and raises and clears alarms.
The following table shows the capabilities of each DS1 circuit pack. The TN722
and TN722B are not supported on G3r V1 or later systems.
ISDN-PRI Trunk signaling (for example, Q.921, Q.931) requires a TN464D and is
handled by system software. The TN464 is covered in the "UDS1-BD (UDS1
Interface Circuit Pack)" section of Chapter 9.
handled by system software. The TN464 is covered in the "UDS1-BD (UDS1
Interface Circuit Pack)" section of Chapter 9.
Each trunk and line have their own maintenance strategies. However, they all
depend on the health of the DS1 Interface circuit pack. Refer to the following
sections for details: TIE-DS1, CO-DS1, DID-DS1, OPS-LINE, ISDN-TRK, and
ISDN-PLK. Signaling over the DS1 link must be synchronized between the
transmitting and receiving ends to ensure error-free communication. Refer to
"SYNC (Synchronization)" for details.
depend on the health of the DS1 Interface circuit pack. Refer to the following
sections for details: TIE-DS1, CO-DS1, DID-DS1, OPS-LINE, ISDN-TRK, and
ISDN-PLK. Signaling over the DS1 link must be synchronized between the
transmitting and receiving ends to ensure error-free communication. Refer to
"SYNC (Synchronization)" for details.
1.
UU is the universal cabinet number (1 for PPN, 2 - 44 for EPNs). C is the carrier designation (A, B,
C, D, or E). SS is the number of the slot in which the circuit pack resides (01 to 21).
C, D, or E). SS is the number of the slot in which the circuit pack resides (01 to 21).
MO Name (in
Alarm Log)
Alarm Level
Initial Command to
Run
1
Full Name of MO
DS1-BD
MAJOR
test board PCSS sh
DS1 Interface Circuit Pack
DS1-BD
MINOR
test board PCSS l
DS1 Interface Circuit Pack
DS1-BD
WARNING
test board PCSS sh
DS1 Interface Circuit Pack
Circuit Pack
Code
24
Channel
32
Channel
Tie Trunk
Signaling
CO Trunk
Signaling
DID
Trunk
Signaling
OPS Line
Signaling
TN722/B
x
x
TN767/B/C/D/E
x
x
x
x
x
TN464C/D/E/F
x
x
x
x
x
x
(24-chl only)