ONKYO ABX-N300 Manual Do Utilizador
En-
15
Basic Operation
—Continued
Note:
Tone adjustments (Bass, Treble, S.Bass) do not affect the
headphones.
Tone adjustments (Bass, Treble, S.Bass) do not affect the
headphones.
1
Press the [TONE] button to make the
display indicate “Tone Control.”
The value of the Bass setting will blink.
display indicate “Tone Control.”
The value of the Bass setting will blink.
2
Use the []/[] buttons to adjust the value.
You can adjust the value in the range of –3 to +3.
You can adjust the value in the range of –3 to +3.
Note:
If you press no buttons for eight seconds, the
previous display will appear automatically.
If you press no buttons for eight seconds, the
previous display will appear automatically.
3
Press the [ENTER] button.
The value of the Treble setting will blink.
The value of the Treble setting will blink.
4
Use the []/[] buttons to adjust the value.
You can adjust the value in the range of –3 to +3.
You can adjust the value in the range of –3 to +3.
Note:
If you press no buttons for eight seconds, the
previous display will appear automatically.
If you press no buttons for eight seconds, the
previous display will appear automatically.
5
Press the [ENTER] button.
The original display will reappear.
The original display will reappear.
To turn on Super Bass, press the [S.BASS] button.
The “S.BASS” indication will appear on the display.
The “S.BASS” indication will appear on the display.
The strength of the ultra-low range will change each time
you press the [S.BASS] button.
The “S.BASS” indication will disappear when this
setting is off.
you press the [S.BASS] button.
The “S.BASS” indication will disappear when this
setting is off.
You can connect a pair of stereo headphones (ø3.5 mm,
1/8-inch phone plug) to the ABX-N300’s headphones
[] jack (see page 11) for private listening.
1/8-inch phone plug) to the ABX-N300’s headphones
[] jack (see page 11) for private listening.
Notes:
• Always turn down the volume before connecting your
• Always turn down the volume before connecting your
headphones.
• If headphones are connected, no beep will be heard
when you operate the touch screen of the ABX-N300.
• While the headphones plug is inserted in the
headphones [] jack, the speakers are turned off.
• If the input is set to iPod or Rocketboost™ (North
American models only), no sound will be output from
the headphones. Disconnect the headphones and listen
via the speakers.
the headphones. Disconnect the headphones and listen
via the speakers.
You can silence the beep tone that is heard when you
operate the touch screen of the ABX-N300.
operate the touch screen of the ABX-N300.
1
While the ABX-N300 is in standby mode,
press the remote controller’s [MENU]
button.
press the remote controller’s [MENU]
button.
2
Use the []/[] buttons to select “Beep,”
and press the [ENTER] button.
and press the [ENTER] button.
3
Use the []/[] buttons to select “Off,” and
press the [ENTER] button.
press the [ENTER] button.
Tip:
If you want to re-enable the beep tone, choose “On” in
step
If you want to re-enable the beep tone, choose “On” in
step
3
of the procedure above.
Adjusting the Bass and Treble
(remote controller only)
(remote controller only)
Using Super Bass
(remote controller only)
(remote controller only)
S.BASS
S.Bass Off
S.Bass On
(default setting)
Using Headphones
Silencing the beep tone during
operation (remote controller only)
operation (remote controller only)