Epson S1C33L03 Manual Do Utilizador

P20/#DRD

I/O

–

I/O port / #DRD output

CFP20(D0)/P2 function select register(0x402D8)

P21/#DWE/
#GAAS

I/O

–

I/O port / #DWE output /
GA address strobe output (Ex)

CFP21(D1)/P2 function select register(0x402D8)
CFEX2(D2)/Port function extension register(0x402DF)

P22/TM0

I/O

–

I/O port / 16-bit timer 0 output

CFP22(D2)/P2 function select register(0x402D8)

P23/TM1

I/O

–

I/O port / 16-bit timer 1 output

CFP23(D3)/P2 function select register(0x402D8)

P24/TM2/
#SRDY2

I/O

–

I/O port / 16-bit timer 2 output / Serial IF Ch.2
ready input/output

CFP24(D4)/P2 function select register(0x402D8)

P25/TM3/
#SCLK2

I/O

–

I/O port / 16-bit timer 3 output / Serial IF Ch.2
clock input/output

CFP25(D5)/P2 function select register(0x402D8)

P26/TM4/
SOUT2

I/O

–

I/O port / 16-bit timer 4 output / Serial IF Ch.2
data output

CFP26(D6)/P2 function select register(0x402D8)

P27/TM5/SIN2

I/O

–

I/O port / 16-bit timer 5 output / Serial IF Ch.2
data input

CFP27(D7)/P2 function select register(0x402D8)

P30/#WAIT/
#CE4&5

I/O

–

I/O port / #WAIT input (I) / #CE4&5 output (O) CFP30(D0)/P3 function select register(0x402DC)

P31/#BUSGET/
#GARD

I/O

–

I/O port / #BUSGET output /
GA read signal output (Ex)

CFP31(D1)/P3 function select register(0x402DC)
CFEX3(D3)/Port function extension register(0x402DF)

P32/#DMAACK0
/#SRDY3

I/O

–

I/O port / #DMAACK0 output / Serial IF Ch.3
ready input/output

CFP32(D2)/P3 function select register(0x402DC)

P33/#DMAACK1
/SIN3

I/O

–

I/O port / #DMAACK1 output / Serial IF Ch.3
data input

CFP33(D3)/P3 function select register(0x402DC)

P34/#BUSREQ/
#CE6

I/O

–

I/O port / #BUSREQ input (I) / #CE6 output
(O)

CFP34(D4)/P3 function select register(0x402DC)

P35/#BUSACK

I/O

–

I/O port / #BUSACK output

CFP35(D5)/P3 function select register(0x402DC)

(I): Input mode, (O): Output mode, (Ex): Extended function

At cold start, all pins are set for I/O ports Pxx (function select register CFPxx = "0"). When these pins are used for

the internal peripheral circuits, write "1" to CFPxx. For details on pin functions in this case, refer to the description

of each peripheral circuit in this manual.

At hot start, the pins retain their state from prior to the reset.

In addition to being an I/O port, the P10–P13, P15–P16, P30 and P34 pins are shared with two types (three types

for P10–P13) of peripheral circuits. The type of peripheral circuit for which these pins are used is determined by

the direction (input or output) in which the pin is set using an I/O control register, as will be described later.

The P04–P07, P10–P14, P21 and P31 ports have extended functions indicated with (Ex) in the table. They can be

selected by writing "1" to CFEXx / Port function extension register (0x402DF).

The setting of CFEXx has priority over the CFPxx.

At cold start, CFEX1 and CFEX0 are set to "1", so the P10–P14 pins are set for debug signal outputs.

The I/O ports are directed for input or output modes by writing data to an I/O control register corresponding to

each port bit.

P07–P00 I/O control: IOC0[7:0] (D[7:0]) / P0 I/O control register (0x402D2)

P16–P10 I/O control: IOC1[6:0] (D[6:0]) / P1 I/O control register (0x402D6)

P27–P20 I/O control: IOC2[7:0] (D[7:0]) / P2 I/O control register (0x402DA)

P35–P30 I/O control: IOC3[5:0] (D[5:0]) / P3 I/O control register (0x402DE)

To set an I/O port for input, write "0" to the I/O control bit. I/O ports set for input mode are placed in the high-

impedance state, and thus function as input ports.

In the input mode, the state of the input pin is read directly, so the data is "1" when the pin state is high (V

DD

 level)

or "0" when the pin state is low (V

SS

 level).

Even in the input mode, data can be written to the data register without affecting the pin state.

To set an I/O port for output, write "1" to the I/O control bit. I/O port set for output function as output ports. When

the port output data is "1", the port outputs a high level (V

DD

 level); when the data is "0", the port outputs a low

level (V

SS

 level).

At cold start, the I/O control register is set to "0" (input mode).

At hot start, the pins retain their state from prior to the reset.

Note: If pins P10–P14, P15–P16, P30 and P34 are set for use with peripheral circuits, their pin functions

vary depending on the input/output direction control by the IOC1x register.