Fellowes 75Cs Manual Do Utilizador
12
12
PS-77Cs
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
PS-77Cs
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
Feed paper straight into
paper entry and release
or
4
Feed into card/CD
entry and release
When finished
shredding set
to OFF (O)
6
5
12
12
PS-77C
s
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
BASIC PRODUCT MAINTENANCE
All cross-cut shredders require oil for peak performance.
If not oiled, a machine may experience diminished
sheet capacity, intrusive noise when shredding and could
ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty
your waste bin.
If not oiled, a machine may experience diminished
sheet capacity, intrusive noise when shredding and could
ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty
your waste bin.
OILING SHREDDER
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
Gently pull uncut
paper from paper
entry. Plug in.
paper from paper
entry. Plug in.
Set to Off (0)
12
12
PS-77Cs
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
2
Press Auto-On (I)
PAPER OR CD/CARD
BASIC SHREDDING OPERATION
1
Check paper amount
3
Plug in and put
disconnect power
switch in ON (I) position
Continuous operation:
10-12-minute maximum
NOTE: Shredder runs briefly
NOTE: Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
10-12-minutes will trigger
20-minute cool down period.
12
12
12
12
2
5
1
3
1
Set to Reverse (R)
for 2-3 seconds
for 2-3 seconds
Press and hold
Reverse (R)
Reverse (R)
PAPER JAM
2
Alternate slowly back and forth
3
6
Press and hold
Reverse (R)
Reverse (R)
Set to Off (O)
and unplug
4
ADvANCED PRODUCT FEATURES
SAFESENSE
®
TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
TROUBLESHOOTING
A. Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum
operating temperature and needs to cool down. This indicator will remain illuminated and the shredder will
not operate for the duration of the recovery time. See Basic Shredding Operation for more information
about the continuous operation and recovery time for this shredder.
B. Bin Open: The shredder will not run if the bin is open.
When illuminated, close the bin to resume shredding.
C. Remove Paper: When illuminated, press reverse (R) and remove paper.
C. Remove Paper: When illuminated, press reverse (R) and remove paper.
Reduce paper quantity to an acceptable amount and refeed into paper entry.
D. SafeSense
D. SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate
and the shredder will stop shredding.
A
B
C
D
1
Turn the shredder ON
( I) to activate
SafeSense
®
Touch test area and
look for the SafeSense
®
indicator to illuminate
2
SafeSense
®
is active
and working properly
12
12
3