Extreme networks 450 Folheto

© 2008 Extreme Networks, Inc. All rights reserved.

Part Number 100293-00 Rev 02

The Altitude 802.11n AP has two models:
•

Altitude 450: 3 internal antennas

Altitude 451: 3 external antennas, RP-SMA connectors

Unpack the Altitude 802.11n AP from its carton. Also in the carton 
are:
•

one wall mounting bracket

3 screws and 3 wall plugs

one plastic rivet (Save this rivet to secure the Altitude 802.11n AP to 
the bracket.)

For the Altitude 451, the three external antennas are also 
included.

An additional security bracket can be purchased that provides port 
protection and cable management. For more information, contact your Extreme Networks

®

 

representative.

 For the Altitude 451, attach the three antennas to the RP-SMA connectors on 

the Altitude 802.11n AP before mounting on its bracket.

 The bracket shipped with the Altitude 802.11n AP is identical to the bracket 

used with the Altitude 35x/36x models. If you replace an Altitude 35x/36x AP 
with the Altitude 802.11n AP, you can mount the AP on the existing wall bracket.

Using a screwdriver, insert the plastic rivet through the hole at the bottom of the 
bracket and into the Altitude 802.11n AP case. This locks the case to the bracket.

To remove the Altitude 802.11n AP, use a 
screwdriver to take out the rivet.

To remove the Altitude 802.11n AP, release 
the spring clip by inserting an Allen key 
(or other similar tool) into the small hole at 
the bottom of the bracket. Then slide the 
case up the bracket and lift off the Altitude 
802.11n AP.

 This device must not be connected to a LAN segment with outdoor 

wiring. Ensure that all cables are run correctly to avoid strain. Replace the power 
supply adapter immediately, if it shows any signs of damage.

 Powering up the Altitude 802.11n AP initiates its automatic discovery and 

registration process with the Summit WM Controller. The parameters for this 
process are configured through the Summit WM Graphical User Interface. For 
more information, see the Summit WM User Guide.

Power up the Altitude 802.11n AP in one of three ways:
• Power over Ethernet (PoE)
• Power over Ethernet: Adding PoE injector
• Power by AC adaptor

If your network is already set up with PoE (802.3af compliant), attach the LAN Ethernet 
cable to the RJ45 Ethernet connector in the top of the Altitude 802.11n AP.

If your network is not set up with PoE, you can provide power to the Ethernet cable with a 
PoE injector. The PoE injector must be 802.3af compliant. The PoE injector is not provided 
with the Altitude 802.11n AP. 

An optional AC power module can be used to power the Altitude 11n AP from an AC 
power source. It can be purchased from Extreme Networks. The part number is 15802. You 
need to separately procure a region-specific AC power cord that plugs into the standard 
IEC C14 socket in the power module.

Power Module Specifications:
Input: 50-60Hz, 100-240 VAC; Output Voltage 48V DC, Max Amps = 0.38A.

Connect the power module to the Altitude 11n AP and then plug the power module to the 
AC outlet.

Use only a safety-approved POE injector or a safety-approved Limited Power Source 
(Class 2) AC adaptor.

Using the 3 screws, mount the Altitude 
802.11n AP wall bracket. Mount it near 
the LAN Ethernet cable plug coming 
from the wall.

Press the back of the Altitude 802.11n AP 
onto the bracket, aligning it with the 
open notches in the bracket. Then slide it 
down until the security spring clip holds 
it in place.

Opening for rivet

Opening for Allen key

Console Port

[Optional]. Connect

the AC power module

if PoE is not being

used in your network.

Attach a screw, and

then fasten the

cables using a tie

wrap to the screw to

provide strain relief.

Connect the LAN 

Ethernet cable to the 

Ethernet port.