Manualsbrain.com
  1. Manuais
  2. Marcas
  3. Dialogic
  4. IPT10000C
  5. Folheto

Dialogic IPT10000C Folheto

Download
Página de 2
Dialogic
®
 
IPT10000C IP Board 
Quick Install Card 
 
                                      
Part Number 64-0082-02 
Copyright © 2004-2007  
Dialogic Corporation.     
All Rights Reserved. 
 
Before You Begin 
Protecting the Board from Damage 
CAUTION: 
All computer boards are sensitive to 
electrostatic discharge (“ESD”).  Handle all static-
sensitive boards and components at a static-safe work 
area, and observe anti-static precautions at all times. 
 
If you are not familiar with ESD safety precautions, visit 
 
Unpacking the Board 
 
Unpack the Dialogic
®
 IPT10000C IP Board (“board”) 
according to the following steps: 
1.  Prepare a static-safeguarded work area. 
2.  Carefully remove the board from the shipping 
carton and anti-static packaging.  Handle the 
board by the edges and avoid touching the 
board’s components. 
3.  Lay the board on the static-dissipative work 
surface. 
Note: Place boards in static-shielding bags when 
carrying boards from station to station. 
CAUTION: Do not remove the board from the anti-static 
packaging until you are ready to install it.  Observe 
proper anti-static precautions at all times. 
 
Installing the Hardware 
Note:  The hardware must be installed before the system 
software. 
1.  Turn the power to the chassis OFF if you do not have 
a live insertion system. If you have live insertion 
capability, the power to the chassis can remain ON. 
 
2.  Remove the cover plate or open front chassis  door. 
3.  Select an empty peripheral expansion bus slot. 
4.  Use the slot’s board guides as you insert the board 
into the chassis slot. Make sure that the tabs on the 
board extractors engage the guide holes in the 
chassis card cage, then lock down the board 
extractors until the red locking tabs snap shut.  
CAUTION:  cPCI backplane pins are bent easily. Make 
sure that the board is seated with hand pressure before 
fully seating board. If the board extractors are used to 
seat the board, make sure to seat evenly. 
Note:  If the power to the chassis is on, power is 
automatically applied to the board, the Out of Service 
LED lights briefly and then goes out, and the Power LED 
goes on. 
Physical Description 
 
4
2
1
5
OUT OF
SERVICE
POWER
7
8
9
10
CompactPCI
ETHERNET
STATUS
100BT0
100BT1
1000BT0
1000BT1
3
6
11
 
 
5
2
2
3
12
12
13
13
15
17
18
19
14
16
1000BT0
100BT0
100BT1
1000BT1
3
20
 
Main Board
 
Rear I/O Module 
 
1.  Power LED  
2.  Green LED: Link Established indicator for 100BASE-TX port  
3.  Green LED: Link Established indicator for 1000BASE-T port  
4.  Out of Service LED: Indicates board is out of service or in reset from 
the host.  
5.  Board Extractor (with red locking tab)  
6.  J1: Connector to Compact PCI backplane  
7.  J2: Connector to Compact PCI backplane  
8.  J3: Connector to Compact PCI backplane  
9.  J4: Connector to Compact PCI backplane  
10. J5: Connector to Compact PCI backplane  
11. Baseboard retaining screw  
12. Yellow LED: Activity indicator for 100BASE-TX port 
 
 
13. Yellow LED: Link Not Established indicator for 
1000BASE-T port  
14. 100BT 0: Port 0 connector to 100BASE-TX Ethernet 
Network  
15. 100BT 1: Port 1 connector to 100BASE-TX Ethernet 
Network  
16. 1000BT 0: Port 0 connector to 1000BASE-T 
Ethernet Network  
17. 1000BT 1: Port 1 connector to 1000BASE-T 
Ethernet Network  
18. J5: Rear I/O module connector to Compact PCI 
backplane  
19. J3: Rear I/O module connector to Compact PCI 
backplane  
20. Rear I/O module retaining screw