Dialogic D/82JCT-U Folheto

Note:  Full H.100 capabilities are not available with 
this release of the Dialogic

®

 D/82JCT-U. 

1.  Attach the end connector on the ribbon cable to 

the CT Bus edge connector on the top edge of the 
first board. The connectors are designed to fit 
together one way only. If the connector does not 
seat fully on the board, turn the cable around and 
try again. Make sure that the colored stripe on the 
cable faces toward the rear bracket. (The stripe 
should be adjacent to pin 1 on the board 
connector.) To preserve the electrical integrity of 
the CT Bus, use a CT Bus cable with the 
appropriate number of connectors (“drops”). It is 
recommended that no more than two connectors 
at either end of the cable be left unused.  

2.  Attach the ribbon cable to the next board until all 

boards are connected by the cable. 

NOTE:
Your CT Bus cable may 
have a different number 
of connectors (drops). 

CT Bus

Cable

Colored

Stripe

(Pin 1)

 

Note:  To connect the CT Bus to an SCbus, attach 
a CT Bus/SCbus Adapter (not included) to the CT 
Bus board closest to the SCbus, and connect the 
SCbus cable to this adapter. See the hardware 
installation instructions for the CT Bus/SCbus 
Adapter for more information. 

3.  If the ribbon cable has extra connectors or loose 

cable, tuck the cable down so that it does not snag 
when you replace the PC cover. 

4.  After installing and connecting all the boards, 

replace the PC cover, cables, and cords. 

 

A PBX station interface cable assembly that is specific 
to the Dialogic

®

 D/82JCT-U (available separately) is 

used to connect the board to a punch-down block. 

  

 

The station interface cable terminates at the punch-
down block end with a 25-pair, 57-series Amphenol 
plug to allow available type-66 punch-down blocks to 
be used to terminate the PBX station wiring. A 36-
position mini-D connector is used on the Dialogic

®

 

D/82JCT-U end of the cable. 

To connect your Dialogic

®

 D/82JCT-U board to a 

punch-down block, follow the instructions below: 
1.  Connect the station interface cable’s 36-position 

mini-D cable plug to the connector on the rear 
bracket of the Dialogic

®

 D/82JCT-U. 

2.  Connect the station interface cable’s 25-pair telco 

plug to the connector on the punch-down block. 

Hardware installation is now complete. 

 

The Telco plug cable connector tabulation is arranged 
so that the four conductors of one station set circuit 
are adjacent on a standard, type-66 punch-down 
block. The pattern shown in the following figure 
continues down the connector to encompass all eight 
channels with two pairs of conductors per channel, for 
a total of 16 twisted conductor pairs. 

2

6

1

 

 

After installing the hardware, run the Dialogic

®

 

Configuration Manager (DCM) as described in the 
installation instructions included with the Dialogic

®

 

System Software to configure your system. 

For technical specifications and product information 
go to: 

.            

For specific warranty information for this board, refer 
to the Warranty section of the Products page, located 
at this URL: http://www.dialogic.com/warranties/.  

Dialogic provides technical support for its products 
through a network of value added distributors who are 
trained to answer technical questions on installing and 
configuring Dialogic

®

 products.  If you are unsure how 

to contact your support channel, please call Dialogic 
in the United States at 973-967-6600 (9am-5pm EST) 
and we will assist in obtaining the appropriate support 
channel. 

 

Outside the United States please refer to 

local contact information. Dialogic also provides direct 
support via Dialogic

®

 Pro™ Services agreements.  For 

more details of direct support from Dialogic please 
refer to: 

. 

To return a board for warranty repair or any other 
returns, please refer to the following: 

. 

If you have a sales question, please contact your 
local Sales Representative or the Regional Sales 
Office for your area. Address, telephone and fax 
numbers, are available at the Dialogic website located 
at: 

. 

 

To purchase Dialogic

®

 products, please refer to the 

following website to locate the appropriate supplier:  

. 

All contents of this document are furnished for informational use only 
and are subject to change without notice and do not represent a 
commitment on the part of Dialogic Corporation or its subsidiaries 
(“Dialogic”). Reasonable effort is made to ensure the accuracy of the 
information contained in the document. However, Dialogic does not 
warrant the accuracy of this information and cannot accept 
responsibility for errors, inaccuracies or omissions that may be 
contained in this document.  

INFORMATION IN THIS DOCUMENT IS PROVIDED IN 
CONNECTION WITH DIALOGIC

®

 PRODUCTS. NO LICENSE, 

EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO 
ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY 
THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED 
AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC 
ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC 
DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, 
RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS 
INCLUDING LIABILITY OR WARRANTIES RELATING TO 
FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, 
OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY 
RIGHT OF A THIRD PARTY. 

Dialogic products are not intended for use in medical, life saving, life 
sustaining, critical control or safety systems, or in nuclear facility 
applications. 

It is possible that the use or implementation of any one of the concepts, 
applications, or ideas described in this document, in marketing 
collateral produced by or on web pages maintained by Dialogic may 
infringe one or more patents or other intellectual property rights owned 
by third parties. Dialogic does not provide any intellectual property 
licenses with the sale of Dialogic products other than a license to use 
such product in accordance with intellectual property owned or validly 
licensed by Dialogic and no such licenses are provided except pursuant 
to a signed agreement with Dialogic. More detailed information about 
such intellectual property is available from Dialogic’s legal department 
at 9800 Cavendish Blvd., 5

th

 Floor, Montreal, Quebec, Canada H4M 

2V9. Dialogic encourages all users of its products to procure all 
necessary intellectual property licenses required to implement any 
concepts or applications and does not condone or encourage any 
intellectual property infringement and disclaims any responsibility 
related thereto. These intellectual property licenses may differ 
from country to country and it is the responsibility of those who 
develop the concepts or applications to be aware of and comply 
with different national license requirements.  

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol, 
among others, are either registered trademarks or trademarks of 
Dialogic. Dialogic's trademarks may be used publicly only with 
permission from Dialogic. Such permission may only be granted by 
Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, 
Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's 
trademarks will be subject to full respect of the trademark guidelines 
published by Dialogic from time to time and any use of Dialogic’s 
trademarks requires proper acknowledgement.  The names of actual 
companies and products mentioned herein are the trademarks of their 
respective owners.