3com MSR 20 Manual Do Utilizador
MIM-IMA-4E1/MIM-IMA-8E1 Module
131
w
WARNING: Laser danger: Invisible laser radiation may be emitted from the
fiber-optic ports which are connected to lasers. To protect your eyes against
radiation harm, never stare into an open fiber-optic port.
fiber-optic ports which are connected to lasers. To protect your eyes against
radiation harm, never stare into an open fiber-optic port.
Step 1: Insert the SFP optical module into its corresponding slot.
Step 2: Locate the Rx and Tx ports of the GE interface. Connect them to another
device with two optical fibers: Rx to Tx and Tx to Rx.
device with two optical fibers: Rx to Tx and Tx to Rx.
Step 3: Check the status of LINK LED on the GE port: ON means the link is
connected and OFF means the link is not connected. In the latter case, check the
line.
connected and OFF means the link is not connected. In the latter case, check the
line.
Connecting Ethernet electrical cable
Step 1: (Use a crossover cable for the connection to a PC/router and
straight-through cable to a Hub/LAN Switch.) Plug one end of the cable to an
Ethernet port of the Router and another end to the desired peer device;
straight-through cable to a Hub/LAN Switch.) Plug one end of the cable to an
Ethernet port of the Router and another end to the desired peer device;
Step 2: Check the status of LINK LED on the module panel: ON means the link is
connected and OFF means the link is not connected. In the latter case, check the
line
connected and OFF means the link is not connected. In the latter case, check the
line
MIM-IMA-4E1/MIM-IM
A-8E1 Module
A-8E1 Module
Introduction
The 4-port/8-port E1 ATM inverse multiplexing interface module
(MIM-IMA-4E1/MIM-IMA-8E1) provides four/eight E1 interfaces that support the
IMA (inverse multiplexing for ATM) technology.
(MIM-IMA-4E1/MIM-IMA-8E1) provides four/eight E1 interfaces that support the
IMA (inverse multiplexing for ATM) technology.
The IMA technology combines multiple low-speed links into a group to support a
high-speed ATM cell stream: It distributes an ATM cell stream over multiple
low-speed E1 links on cell by cell basis at the transmission end and reassembles
the cells on the low-speed E1 links into the original stream at the far end. This
technology provides a scalable and cost-effective solution, and is commonly used
in plesiochronous digital hierarchy (PDH) networks to transport ATM cells.
high-speed ATM cell stream: It distributes an ATM cell stream over multiple
low-speed E1 links on cell by cell basis at the transmission end and reassembles
the cells on the low-speed E1 links into the original stream at the far end. This
technology provides a scalable and cost-effective solution, and is commonly used
in plesiochronous digital hierarchy (PDH) networks to transport ATM cells.
Interface Attributes
The following table describes the interface attributes of the
MIM-IMA-4E1/MIM-IMA-8E1 module:
MIM-IMA-4E1/MIM-IMA-8E1 module:
Table 90 Interface attributes of the MIM-IMA-4E1/ MIM-IMA-8E1
Attribute
Description
MIM-IM
A-4E1
(75-ohm
)
A-4E1
(75-ohm
)
MIM-IMA-8E1
(75-ohm)
(75-ohm)
MIM-IMA-4E1
(120-ohm)
(120-ohm)
MIM-IMA-8E1
(120-ohm)
(120-ohm)
Connector DB68
Number of
connectors
connectors
1
Interface
standard
standard
ITU-G.703, ITU-G.704
Interface rate
2.048 Mbps