Avaya X330W2-DS1 Manual Do Utilizador
Chapter 3
Initial Configuration
24
Avaya X330W-2DS1 User’s Guide
To configure E1 or T1 interfaces:
1
1
Use the "show controllers" [<port>] command to check if your
controller’s mode is configured as E1 or T1.
Use the "ds-mode" [e1|t1]command to set the controller’s mode to E1 or T1.
Changing the line type causes the module to reset.
controller’s mode is configured as E1 or T1.
Use the "ds-mode" [e1|t1]command to set the controller’s mode to E1 or T1.
Changing the line type causes the module to reset.
2
Use the "controller" {e1|t1} <port-number> command to set the port
number to be configured.
The prompt changes to X330WAN-2DS1-N(super-controller:n)#
where N is the switch number and n is the port number.
number to be configured.
The prompt changes to X330WAN-2DS1-N(super-controller:n)#
where N is the switch number and n is the port number.
3
Use the following commands if you want to change the clock source, frame type
and linecode parameters from their default settings:
"clock source"
and linecode parameters from their default settings:
"clock source"
{line|internal}
"framing"
{sf|esf} for T1 lines or "framing" {crc4|no-crc4} for E1
lines.
"linecode"
"linecode"
{ami|b8zs}
for T1 lines or "linecode" {ami|hdb3} for E1
lines.
“cablelength”
“cablelength”
{long|short}
for T1 lines.
If you are working in E1 mode, go to step 4, otherwise go to step 5.
4
Use the channel-group channel-no timeslots timeslot-list command to specify
the channel group and time slots to be mapped. For example, typing
channel group 1 timeslots 1,3-5,7
the channel group and time slots to be mapped. For example, typing
channel group 1 timeslots 1,3-5,7
configures time slots numbered 1,
3-5 and 7 to be mapped in channel-group number 1.
Proceed to step 6.
Proceed to step 6.
5
Use the channel-group channel-no timeslots timeslot-list
speed <56|64>
speed <56|64>
command to specify the channel group, time slots to be
mapped and DS0 speed in kbps. For example, typing
channel group 1 timeslots 1,3-5,7 speed 64
channel group 1 timeslots 1,3-5,7 speed 64
configures time slots
numbered 1, 3-5 and 7 to be mapped in channel-group number 1 and the DS0
speed to 64 kbps.
The default DS0 speed is 56 kbps
speed to 64 kbps.
The default DS0 speed is 56 kbps
6
Type exit to return to Supervisor mode.
The prompt returns to X330WAN-2DS1-N(super)#
The prompt returns to X330WAN-2DS1-N(super)#
7
Use the
"interface Serial"
"interface Serial"
[port:channel-group[.ip-interface]]
command to configure each channel group as a virtual serial interface. Specify
the port number and channel group number to modify.
For example, typing interface Serial 1:1 configures a serial interface on
port number 1 with a channel group number 1.
the port number and channel group number to modify.
For example, typing interface Serial 1:1 configures a serial interface on
port number 1 with a channel group number 1.
8
Use the "ip address" <ip address><mask> command to assign an IP
address and subnet mask to the interface.
address and subnet mask to the interface.
9
Repeat steps 2 through 8 if you want to configure another E1 or T1 interface.
10 Type exit to return to Supervisor mode.
The prompt returns to X330WAN-2DS1-N(super)#