GE GFK-1004B Manual Do Utilizador
5
5-15
GFK-1004B
Chapter 5 The Station Manager
Section 3: Command Descriptions
Symbols are used to denote options or alternatives in the command parameters. These
symbols are used to help give a clear and complete description of the command and are
not part of the command. The use of these symbols is briefly described below:
symbols are used to help give a clear and complete description of the command and are
not part of the command. The use of these symbols is briefly described below:
Arguments to commands are often given symbolic names which are enclosed in angle
brackets (< >). For example; “<PAGE>” is an argument to many commands. The com-
mand specification for “<PAGE>” is described as a number which specifies the page
number of the display. It is important to remember to enter the argument and not its
symbolic name. For example, to see the second page of the Test Results, you should en-
ter:
brackets (< >). For example; “<PAGE>” is an argument to many commands. The com-
mand specification for “<PAGE>” is described as a number which specifies the page
number of the display. It is important to remember to enter the argument and not its
symbolic name. For example, to see the second page of the Test Results, you should en-
ter:
REPORT 2 - not - REPORT <PAGE>
Optional arguments are surrounded by square brackets, for example REPORT [<PAGE>].
Again, the brackets should not be entered as part of the command.
Again, the brackets should not be entered as part of the command.
Sometimes there are several alternatives for an argument. The alternatives are listed in
the command description separated by a vertical bar (|) and enclosed in braces ({|}).
For example, when using the NET command, only one of the alternatives should be se-
lected:
the command description separated by a vertical bar (|) and enclosed in braces ({|}).
For example, when using the NET command, only one of the alternatives should be se-
lected:
NET { ON | OFF }
Command Input Processing
Anything in a command description that is not one of the constructs discussed above
should be entered exactly as it is shown. All data entered for the command is converted
to lower case unless it is enclosed in double quotes (“”). To use a double quote character
within an argument string, the double quote should be entered twice, for example:
“This string would contain one ” “character.”
should be entered exactly as it is shown. All data entered for the command is converted
to lower case unless it is enclosed in double quotes (“”). To use a double quote character
within an argument string, the double quote should be entered twice, for example:
“This string would contain one ” “character.”
The Station Manager accepts several ASCII control characters for various functions. The
control characters accepted by the Station Manager are listed in the following table. All
other control characters are ignored on normal command inputs. Illegal control charac-
ters sent to the Station Manager result in a BEL character being sent to the terminal.
control characters accepted by the Station Manager are listed in the following table. All
other control characters are ignored on normal command inputs. Illegal control charac-
ters sent to the Station Manager result in a BEL character being sent to the terminal.
Table 5-6. Control Characters
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
Control Character
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Usual Keyboard Function
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Function
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
BS
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Ctrl-H (Backspace)
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Delete previous character
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
DEL
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Delete
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Delete previous character
ÁÁÁÁÁÁÁ
DC1
ÁÁÁÁÁÁÁÁÁÁ
Ctrl-Q
ÁÁÁÁÁÁÁÁÁÁÁ
Resume output to the display
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
DC2
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Ctrl-R
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Recall previous command line
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
DC3
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Ctrl-S
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Stop output to the display
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
CAN
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Ctrl-X
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Cancel the current input line
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
CR
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
Return (Enter)
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Terminate line and execute command
If a command line becomes too long to easily type on a single display line, the character
pair “\<RET>” can be used to continue the command on the next line on the display.
The “\” (backslash) character will not be used as a part of any argument.
pair “\<RET>” can be used to continue the command on the next line on the display.
The “\” (backslash) character will not be used as a part of any argument.