Savin C7526dn Manual Do Utilizador
Remove the protective sheet, as shown.
Pinch the orange tape, and then pull it
out.
Pinch the orange tape, and then pull it
out.
AET806S
Turn the green lever clockwise to lock
the unit.
the unit.
AET146S
Close the inner cover. Lock the inner
cover by pressing in (
cover by pressing in (
) and then
turning the two green levers clockwise
(
(
).
AQC014S
Close the left cover.
Close the left cover firmly using both hands, until it
clicks into place.
clicks into place.
Open the top cover by grasping the
handles on the left and right sides.
handles on the left and right sides.
AQC007S
Turn the two green levers
counterclockwise (
counterclockwise (
), and then slowly
open the inner cover (
).
AQC032S
Remove the end of the tape from the pinter.
AET802S
Remove the four pieces of tape from
the photo conductor unit.
the photo conductor unit.
AET803S
Remove the securing pin, as shown,
from the transfer unit. Pinch it, and
then pull it out.
from the transfer unit. Pinch it, and
then pull it out.
AET804S
Turn the green lever of the transfer unit
counterclockwise to unlock the unit.
counterclockwise to unlock the unit.
AET805S
❖ Optimum Environmental Conditions
Permissible and recommended temperature and
humidity ranges are as follows:
humidity ranges are as follows:
%RH
TS4K031KE
• White area: Permissible Range
• Gray area: Recommended Range
• Gray area: Recommended Range
• The machine must be level within 5 mm, 0.2˝ from
both front to rear and left to right.
• To avoid possible build-up of ozone, locate this
machine in a large well ventilated room that has an
air turnover of more than 30 m
air turnover of more than 30 m
3
/hr/person.
• When you use this machine for a long time in a
confined space without good ventilation, you may
detect an odd smell. To keep the workplace
comfortable, we recommend you keep it well
ventilated.
detect an odd smell. To keep the workplace
comfortable, we recommend you keep it well
ventilated.
❖
Space Required for Installation
• Areas exposed to direct sunlight or strong light
• Dusty areas
• Areas with corrosive gases
• Areas that are excessively cold, hot, or humid
• Locations near air conditioners or humidifiers
• Locations near other electronic equipment
• Locations subject to frequent strong vibration
• Dusty areas
• Areas with corrosive gases
• Areas that are excessively cold, hot, or humid
• Locations near air conditioners or humidifiers
• Locations near other electronic equipment
• Locations subject to frequent strong vibration
❖ Power Source
Connect the power cable to a power source of the
following specification:
following specification:
• 120 V, 60 Hz, 11 A or more
Quick Installation Guide
Read this manual carefully before you use the product and keep it handy for future reference.
For safe and correct use, please be sure to read the Safety Information in “Safety Information”
before using the machine.
For safe and correct use, please be sure to read the Safety Information in “Safety Information”
before using the machine.
Unpacking
To protect it from shock and vibration during transit,
this printer comes packaged in cushioning foam and
secured with tape. Remove these protective materials
after bringing the machine to where it will be installed.
this printer comes packaged in cushioning foam and
secured with tape. Remove these protective materials
after bringing the machine to where it will be installed.
Caution
• When lifting the machine, use the inset grips on both
sides. The printer could break or cause an injury if
dropped.
dropped.
• Place no objects on the left or inner cover.
• Be sure to remove all four strips of tape from the
photo conductor unit to avoid malfunction.
• Removed tape is dirty. Be careful not to let it touch
your hands or clothes.
Remove the plastic bag.
Lift the printer with two people by using
the inset grips on both sides of the printer.
the inset grips on both sides of the printer.
AET034S
• Leave the tape holding the paper feed tray and cover
in place while moving the printer.
• Lower the machine slowly and carefully to prevent
trapping your hands.
Remove the orange adhesive tape from
the printer body.
the printer body.
Open the left cover. Do not remove the
orange tape attached to the left cover.
orange tape attached to the left cover.
AQC026S
Checking the Contents of
the Box
the Box
Follow the procedure below to verify the items that
come with the printer.
come with the printer.
• Ensure that the box contains all items listed below. If
there are any missing or defective items, contact your
sales representative.
sales representative.
❖ Manuals and CD-ROMs
Quick Installation Guide (This manual)
CD-ROM “Printer Drivers and Utilities”
CD-ROM “Manuals”
CD-ROM “Document Management Utility”
CD-ROM “Printer Drivers and Utilities”
CD-ROM “Manuals”
CD-ROM “Document Management Utility”
Ferrite Core x 2
AET510S
Toner Cartridges: Black (K), Magenta (M), Cyan
(C), Yellow (Y)
AET028S
Paper Feed Unit Labels
AET031S
Color Calibration Sample Sheet
Additional Documentation
• This package does not include an interface cable.
Purchase one to use with your host computer. See
“Appendix”, Hardware Guide.
“Appendix”, Hardware Guide.
Where to Put the Printer
The printer’s location should be carefully chosen
because environmental conditions greatly affect its
performance.
because environmental conditions greatly affect its
performance.
Warning
• Confirm that the wall outlet is near the machine and
freely accessible, so that in event of an emergency, it
can be unplugged easily.
can be unplugged easily.
• Only connect the machine to the power source
described on this manual.
• Avoid multi-wiring.
• Do not damage, break or make any modifications to
• Do not damage, break or make any modifications to
the power cord. Do not place heavy objects on it, pull
it hard or bend it more than necessary. These actions
could cause an electric shock or fire.
it hard or bend it more than necessary. These actions
could cause an electric shock or fire.
• The supplied power cord is for use with this equipment
only. Do not use with other appliances. Doing so may
result in fire, electric shock, or injury.
result in fire, electric shock, or injury.
Caution
• Do not handle the plug with wet hands. Doing so might
cause an electrical shock.
• Keep the machine in an area that is within optimum
environmental conditions. Operating the machine in
an environment that is outside the recommended
ranges of humidity and temperature can cause an
electrical fire hazard. Keep the area around the socket
free of dust. Accumulated dust can become an
electrical fire hazard.
an environment that is outside the recommended
ranges of humidity and temperature can cause an
electrical fire hazard. Keep the area around the socket
free of dust. Accumulated dust can become an
electrical fire hazard.
• Place the machine on a strong and level surface.
Otherwise, it might fall and injure someone.
• If you use the machine in a confined space, ensure
there is continuous air circulation.
❖ Space Required for Installation
Leave enough space around the printer. This space is
necessary to operate the printer. The recommended (or
minimum) space requirements are as follows:
necessary to operate the printer. The recommended (or
minimum) space requirements are as follows:
AQC025S
A: 50 cm (19.7 inches) or more
B: 10 cm (4 inches) or more
C: 10 cm (4 inches) or more
D: 70 cm (27.6 inches) or more
B: 10 cm (4 inches) or more
C: 10 cm (4 inches) or more
D: 70 cm (27.6 inches) or more
CLP27DN/CLP31DN/C7526dn/C7531dn/LP226cn/
LP231cn/Aficio SP C410DN/Aficio SP C411DN