Savin 1232 Manual Do Utilizador
Troubleshooting
34
4
Machine Does Not Print
Possible Cause
Solutions
Is the power on?
Confirm the cable is securely plugged into the power outlet and
the machine.
the machine.
Turn on the main power switch.
Is the machine online?
If not, press [Online] on the display panel.
Does the printer function
status indicator stay red?
status indicator stay red?
If so, check the error message on the display panel and take the re-
quired action.
quired action.
Is there a warning status or
error message on the dis-
play panel?
error message on the dis-
play panel?
If so, check the error message or warning status on the display
panel and take the required action.
panel and take the required action.
Can you print a configura-
tion page?
tion page?
If you cannot print a configuration page, there maybe a machine
malfunction. Contact your sales or service representative.
malfunction. Contact your sales or service representative.
See p.52 “Machine Condition” for printing a configuration page.
Is the interface cable con-
nected securely to the ma-
chine and the computer?
nected securely to the ma-
chine and the computer?
Connect the interface cable securely. If it has a fastener, fasten that
securely as well.
securely as well.
See “Connecting the Machine”, Printer Reference 1.
Are you using the correct
interface cable?
interface cable?
The type of interface cable you should use depends on the com-
puter. Be sure to use the correct one. If the cable is damaged or
worn, replace it.
puter. Be sure to use the correct one. If the cable is damaged or
worn, replace it.
See “Connecting the Machine”, Printer Reference 1.
Was the interface cable
connected after the ma-
chine was turned on?
connected after the ma-
chine was turned on?
Connect the interface cable before turning on the machine.
Is the signal status satisfac-
tory when using wireless
LAN in Infrastructure
mode ?
tory when using wireless
LAN in Infrastructure
mode ?
To check the signal status, press
{{{{User Tools/Counter/Inquiry}}}} on the
control panel, and then [System Settings] on the display panel. On
the [Interface Settings] tab, select [IEEE 802.11b] and then press [Wire-
less LAN Signal]
the [Interface Settings] tab, select [IEEE 802.11b] and then press [Wire-
less LAN Signal]
. If signal quality is bad, move the machine to a lo-
cation where signals pass or remove any objects that block signals.
When using Wireless LAN,
is the SSID correctly set?
is the SSID correctly set?
Confirm the machine's display panel that the SSID is correctly set.
See “Interface Settings/IEEE 802.11b (Option)”, General Settings Guide.
When using a Wireless
LAN, is the access point
correctly set?
LAN, is the access point
correctly set?
Confirm the access point settings when in Infrastructure mode.
Depending on the access point, client access may be limited by the
MAC address.
Depending on the access point, client access may be limited by the
MAC address.
Also, confirm there are no problems in transmission between ac-
cess point and wired clients, and between access point and wire-
less clients.
cess point and wired clients, and between access point and wire-
less clients.
When using Wireless LAN,
is the LED on the Wireless
LAN card lit or blinking?
is the LED on the Wireless
LAN card lit or blinking?
Confirm the orange LED is lit, and the green LED is lit or blinks
during transmission.
during transmission.
Is the Wireless LAN being
used in Ad Hoc mode?
used in Ad Hoc mode?
In that case, turn the main power switch off and on. Also, chang-
ing some of the settings in [Network] on the [Interface Settings] tab in
[System Settings]
ing some of the settings in [Network] on the [Interface Settings] tab in
[System Settings]
on the display panel may solve the problem.