Nortel Networks 5530 Manual Do Utilizador

Página de 72
Filters and QoS Configuration for ERS 5500 
Technical Configuration Guide   
   
  
v2.0 
              
 
 
 NN48500-559   
 
 
___________________________________________________________________________________________________________________________ 
Nortel Confidential Information   Copyright © 2008 Nortel Networks. All Rights Reserved. 
 
 
 
 
 
 
External Distribution
 
 
 
 
                              19
 
5.  Traffic Meter and Shaping 
The Ethernet Routing Switch 5500 supports both policing/metering of ingress traffic in addition to 
egress port shaping. The meter and shape range is as shown in table 6 below. Please note that 
all QoS levels are respected and honoured on a shaped interface. 
Table 6: Meter and Shaping Range and Granularity 
Product Meter/Shaper 
Range 
Granularity Bucket 
Size 
ERS5510 
1 Mbps to 1023 Mbps 
1 Mbps 
8 buckets 
ERS5520 
1 Mbps to 1023 Mbps 
1 Mbps 
8 buckets 
ERS5530 
(10M/100M,1G) 
64 Kbps to 1023 
Mbps 
64 Kbps 
8 buckets 
ERS5530 (10G) 
1 Mbps to 1023 Gbps 
1 Mbps 
12 buckets 
When configuring traffic metering or shaping, a committed rate, a maximum burst size and burst 
duration is entered. The maximum burst rate and burst duration is used along with the committed 
rate to setup a fixed token bucket where each token represents 1 byte. Up to eight fixed bucket 
sizes are supported for all 10/100 Mbps and GigE ports. Up to twelve fixed bucket sizes are 
supported on the ERS5530 only via the 10 GigE interface. The token bucket allows a committed 
burst to occur up to the token bucket size.  
For traffic metering, an in profile and an out of profile action is configured and is expressed as an 
id. You can use one of the default actions or create a new action prior to configuring a meter. To 
view the action id’s, please use the command shown below. For example, if you wish to remark 
the in profile traffic with a QoS level of Bronze and drop traffic for out of profile traffic, select id 3 
and 1 respectively. Please note that you must associate the classifier to identify IP traffic since 
the DSCP value is being remarked.  
 5530-24TFD(config)#show qos action 
 Id         Name       Drop  Update    802.1p     Set Drop   Extension Storage 
                              DSCP    Priority   Precedence             Type 
_____ ________________ _____ ______ ____________ ___________ _________ _______ 
1     Drop_Traffic     Yes   Ignore Ignore       High Drop             ReadOnl 
2     Standard_Service No    0x0    Priority 0   High Drop             ReadOnl 
3     Bronze_Service   No    0xA    Priority 2   Low Drop              ReadOnl 
4     Silver_Service   No    0x12   Priority 3   Low Drop              ReadOnl 
5     Gold_Service     No    0x1A   Priority 4   Low Drop              ReadOnl 
6     Platinum_Service No    0x22   Priority 5   Low Drop              ReadOnl 
7     Premium_Service  No    0x2E   Priority 6   Low Drop              ReadOnl 
8     Network_Service  No    0x30   Priority 7   Low Drop              ReadOnl 
9     Null_Action      No    Ignore Ignore       Low Drop              ReadOnl 
55001 UntrustedClfrs1  DPass Ing 1p Ignore       Low Drop              Other 
55002 UntrustedClfrs2  DPass 0x0    Priority 0   High Drop             Other 
.