Murphy EG21 Manual Do Utilizador
00-02-0251
02-27-08
Section 70
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.
MURPHY, the Murphy logo, and Swichgage
MURPHY, the Murphy logo, and Swichgage
®
are registered and/or common law trademarks of Murphy Industries, Inc. This document, including textual
matter and illustrations, is copyright protected by Murphy Industries, Inc., with all rights reserved. (c) 2008 Murphy Industries, Inc.
EG21 and EGS21 Series Electric Gage and Swichgage
® Installation
for Pressure, Temperature, Fuel Level, Voltmeter and Ammeter
IMPORTANT NOTICE FOR ALL EG21 ELECTRIC GAGES AND EGS21 ELECTRIC
SWICHGAGES FOR 24VDC AND 32VDC APPLICATIONS
A change in the dial illumination circuit has made it necessary to change the external wiring harness.
If you use the incorrect wiring harness, irreparable damage will occur to the gage mechanism.
If you use the incorrect wiring harness, irreparable damage will occur to the gage mechanism.
The table below lists correct wire harness assemblies for units by manufacturing date. For date code
R1 (January 1996) or earlier (Q12, Q11, etc.) the wire harness can be identified by P/N and by
BLACK shrink tubing on the YELLOW wire. For date code R1 (February 1996) and later (R3, R4,
etc.) the wire harness can be identified by P/N and by RED shrink tubing on the YELLOW wire.
R1 (January 1996) or earlier (Q12, Q11, etc.) the wire harness can be identified by P/N and by
BLACK shrink tubing on the YELLOW wire. For date code R1 (February 1996) and later (R3, R4,
etc.) the wire harness can be identified by P/N and by RED shrink tubing on the YELLOW wire.
Date Code R1 or Earlier
Date Code R2 or Later
05004546
05004547
05004548
05004549
05004550
05004551
05004552
05004547
05004548
05004549
05004550
05004551
05004552
05006166
05006167
05006168
05006169
05006170
05006171
05006172
05006167
05006168
05006169
05006170
05006171
05006172
If dial illumination is NOT required, either wire harness can be used on any date code, if the YELLOW
wire is NOT connected.
wire is NOT connected.
Wire/Connector Assembly
NOTE: EG21 Series gage and EGS21 Series Swichgage movement and illumination
require 12VDC to function. For 24 or 32 volt systems, voltage converters are built into the
electrical wire/connector assembly and supplied with instrument.
require 12VDC to function. For 24 or 32 volt systems, voltage converters are built into the
electrical wire/connector assembly and supplied with instrument.
Listed below are replacement part numbers for all wire/connector assemblies. Voltage converter included for 24
and 32 volt. Specify part number when ordering.
and 32 volt. Specify part number when ordering.
12 VDC
24 VDC
32 VDC
EG21P / T / F
05004506
05006166 (05004546)*
05006167 (05004547)*
EGS21P / T / F
05004507
05006168 (05004548)*
05006169 (05004549)*
EG21AM
05004505
05006170 (05004550)*
05006171 (05004551)*
EGS21AM 05004504
05006172
(05004552)*
⎯
EG21VM 05004508
05004508
⎯
EGS21VM 05004504
05004504
⎯
* For gages with date code R1 (January 1996) or earlier (Q12, Q11, etc.,) specify part number shown in parenthesis.
Gage Installation