Netgear M4100-26-POE Manual Do Utilizador
Management Commands
682
ProSafe M4100 and M7100 Managed Switches
no radius server attribute
Use the
no
version of this command to disable the NAS-IP-Address attribute global
parameter for RADIUS client. When this parameter is disabled, the RADIUS client does not
send the NAS-IP-Address attribute in RADIUS requests.
send the NAS-IP-Address attribute in RADIUS requests.
Format
no radius server attribute <4> [<ipaddr>]
Mode
The following shows an example of the command.
(Switch) (Config) #radius server attribute 4 192.168.37.60
(Switch) (Config) #radius server attribute 4
radius server host
Use this command to configure the IP address or DNS name to use for communicating with
the RADIUS server of a selected server type. While configuring the IP address or DNS name
for the authenticating or accounting servers, you can also configure the port number and
server name. If the authenticating and accounting servers are configured without a name, the
command uses the ‘Default_RADIUS_Auth_Server’ and ‘Default_RADIUS_Acct_Server’ as
the default names, respectively. The same name can be configured for more than one
authenticating servers and the name should be unique for accounting servers. The RADIUS
client allows the configuration of a maximum 32 authenticating and accounting servers.
the RADIUS server of a selected server type. While configuring the IP address or DNS name
for the authenticating or accounting servers, you can also configure the port number and
server name. If the authenticating and accounting servers are configured without a name, the
command uses the ‘Default_RADIUS_Auth_Server’ and ‘Default_RADIUS_Acct_Server’ as
the default names, respectively. The same name can be configured for more than one
authenticating servers and the name should be unique for accounting servers. The RADIUS
client allows the configuration of a maximum 32 authenticating and accounting servers.
If you use the <auth> parameter, the command configures the IP address or hostname to
use to connect to a RADIUS authentication server. You can configure up to 3 servers per
RADIUS client. If the maximum number of configured servers is reached, the command fails
until you remove one of the servers by issuing the “no” form of the command. If you use the
optional <port> parameter, the command configures the UDP port number to use when
connecting to the configured RADIUS server. The <port> number range is 1 - 65535, with
1812 being the default value.
use to connect to a RADIUS authentication server. You can configure up to 3 servers per
RADIUS client. If the maximum number of configured servers is reached, the command fails
until you remove one of the servers by issuing the “no” form of the command. If you use the
optional <port> parameter, the command configures the UDP port number to use when
connecting to the configured RADIUS server. The <port> number range is 1 - 65535, with
1812 being the default value.
Note:
To reconfigure a RADIUS authentication server to use the default
UDP <port>, set the <port> parameter to 1812.
If you use the <acct> token, the command configures the IP address or hostname to use for
the RADIUS accounting server. You can only configure one accounting server. If an
accounting server is currently configured, use the “no” form of the command to remove it from
the configuration. The IP address or hostname you specify must match that of a previously
configured accounting server. If you use the optional <port> parameter, the command
configures the UDP port to use when connecting to the RADIUS accounting server. If a
<port>
the RADIUS accounting server. You can only configure one accounting server. If an
accounting server is currently configured, use the “no” form of the command to remove it from
the configuration. The IP address or hostname you specify must match that of a previously
configured accounting server. If you use the optional <port> parameter, the command
configures the UDP port to use when connecting to the RADIUS accounting server. If a
<port>
is already configured for the accounting server, the new <port> replaces the
previously configured <port>. The <port> must be a value in the range 0 - 65535, with
1813 being the default.
1813 being the default.
Global Config