Netgear NETGEAR Manual Do Utilizador
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Quality of Service (QoS) Commands
11-3
202-10088-01, March 2005
The Ethertype may be specified as either a keyword or a four-digit hexadecimal value from
0x0600-0xFFFF. The currently supported <ethertypekey> values are: appletalk, arp, ibmsna,
ipv4, ipv6, ipx, mplsmcast, mplsucast, netbios, novell, pppoe, rarp. Each of these translates into
its equivalent Ethertype value(s).
0x0600-0xFFFF. The currently supported <ethertypekey> values are: appletalk, arp, ibmsna,
ipv4, ipv6, ipx, mplsmcast, mplsucast, netbios, novell, pppoe, rarp. Each of these translates into
its equivalent Ethertype value(s).
The assign-queue parameter allows specification of a particular hardware queue for handling
traffic that matches this rule. The allowed <queue-id> value is 0-(n-1), where n is the number of
user configurable queues available for the hardware platform. The redirect parameter allows the
traffic matching this rule to be forwarded to the specified <slot/port>. The assign-queue and
redirect parameters are only valid for a 'permit' rule.
traffic that matches this rule. The allowed <queue-id> value is 0-(n-1), where n is the number of
user configurable queues available for the hardware platform. The redirect parameter allows the
traffic matching this rule to be forwarded to the specified <slot/port>. The assign-queue and
redirect parameters are only valid for a 'permit' rule.
Format
{deny|permit} {{<srcmac> <srcmacmask} | any} {{<dst-
mac> <dstmacmask>} | any | bpdu} [<ethertypekey> |
<0x0600-0xFFFF>] [vlan {{eq <0-4095>} | {range <0-
4095> <0-4095>}}] [cos <0-7>] [secondary-vlan {{eq <0-
4095>} | {range <0-4095> <0-4095>}}] [secondary-cos
<0-7>] [assign-queue <queue-id>] [redirect <slot/
port>]
Note that the special command form {deny|permit} any any is used to match all Ethernet layer 2
packets, and is the equivalent of the IP access list "match every" rule.
packets, and is the equivalent of the IP access list "match every" rule.
Mode
Mac-Access-List Config
mac access-group <name> {in|out} [sequence <1-4294967295>]
This command attaches a specific MAC Access Control List (ACL) identified by <name> to an
interface in a given direction. The <name> parameter must be the name of an exsiting MAC ACL.
interface in a given direction. The <name> parameter must be the name of an exsiting MAC ACL.
An optional sequence number may be specified to indicate the order of this access list relative to
other access lists already assigned to this interface and direction. A lower number indicates higher
precedence order. If a sequence number is already in use for this interface and direction, the
specified access list replaces the currently attached access list using that sequence number. If the
sequence number is not specified for this command, a sequence number that is one greater than the
highest sequence number currently in use for this interface and direction will be used.
other access lists already assigned to this interface and direction. A lower number indicates higher
precedence order. If a sequence number is already in use for this interface and direction, the
specified access list replaces the currently attached access list using that sequence number. If the
sequence number is not specified for this command, a sequence number that is one greater than the
highest sequence number currently in use for this interface and direction will be used.
This command specified in 'Interface Config' mode only affects a single interface, whereas the
'Global Config' mode setting is applied to all interfaces. The 'Interface Config' mode command is
only available on platforms that support independent per-port class of service queue configuration.
'Global Config' mode setting is applied to all interfaces. The 'Interface Config' mode command is
only available on platforms that support independent per-port class of service queue configuration.
Format
mac access-group <name> {in|out} [sequence <1-
4294967295>]
Mode
Global Config or Interface Config