Netgear NETGEAR Manual Do Utilizador
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
11-26
Quality of Service (QoS) Commands
202-10088-01, March 2005
police-two-rate
This command is used to establish the traffic policing style for the specified class. The two-rate
form of the police command uses two data rates and two burst sizes, resulting in three outcomes:
conform, exceed and violate. The first two data parameters are the conforming data rate and burst
size. The conforming data rate is specified in kilobits-per-second (Kbps) and is an integer from 1
to 4294967295, while the conforming burst size is specified in kilobytes (KB) as an integer from 1
to 128. The next two data parameters are the peak data rate and burst size. The peak data rate is
specified in kilobits-per-second (Kbps) as an integer from 1 to 4294967295, while the peak burst
size is specified in kilobytes (KB) as an integer from 1 to 128. Note that the peak data rate must be
equal to or greater than the conforming data rate.
form of the police command uses two data rates and two burst sizes, resulting in three outcomes:
conform, exceed and violate. The first two data parameters are the conforming data rate and burst
size. The conforming data rate is specified in kilobits-per-second (Kbps) and is an integer from 1
to 4294967295, while the conforming burst size is specified in kilobytes (KB) as an integer from 1
to 128. The next two data parameters are the peak data rate and burst size. The peak data rate is
specified in kilobits-per-second (Kbps) as an integer from 1 to 4294967295, while the peak burst
size is specified in kilobytes (KB) as an integer from 1 to 128. Note that the peak data rate must be
equal to or greater than the conforming data rate.
For each outcome, the only possible actions are drop, set-cos-transmit, set-sec-cos-transmit, set-
dscp-transmit, set-prec-transmit, or transmit. In this two-rate form of the police command, the
conform action defaults to send, the exceed action defaults to drop, and the violate action defaults
to drop. These actions can be set with this command
dscp-transmit, set-prec-transmit, or transmit. In this two-rate form of the police command, the
conform action defaults to send, the exceed action defaults to drop, and the violate action defaults
to drop. These actions can be set with this command
For set-dscp-transmit, a <
dscpval>
value is required and is specified as either an integer from 0 to
63, or symbolically through one of the following keywords:
af11, af12, af13, af21, af22, af23, af31, af32,
af33, af41, af42, af43, be, cs0, cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef
.
For set-prec-transmit, an IP Precedence value is required and is specified as an integer from 0-7.
Format
police-two-rate {<1-4294967295> <1-4294967295> <1-
128> <1-128> conform-action {drop | set-cos-transmit
<0-7> | set-sec-cos-transmit <0-7> | set-prec-trans-
mit <0-7> | set-dscp-transmit <0-63> | transmit}
exceed-action {drop | set-cos-transmit <0-7> | set-
sec-cos-transmit <0-7> | set-prec-transmit <0-7> |
set-dscp-transmit <0-63> | transmit} [violate-action
{drop | set-cos-transmit <0-7> | set-sec-cos-transmit
<0-7> | set-prec-transmit <0-7> | set-dscp-transmit
<0-63> | transmit}]}
Mode
Policy-classmap Config
Restrictions
Only one style of police command (simple, singlerate, tworate) is
allowed for a given class instance in a particular policy.
allowed for a given class instance in a particular policy.
Policy Type
In
Incompatibilities
Mark IP DSCP, Mark IP Precedence