3com 5500-SI Manual Do Utilizador
80
C
HAPTER
4: XRN C
ONFIGURATION
Table 60 Configuring FTM
The Switch 5500 Series: the SI units supports basic XRN, that is, Distributed Device
Management (DDM) and Distributed Link Aggregation (DLA); the EI units support
enhanced XRN, that is DDM, Distributed Resilient Routing (DRR).
Management (DDM) and Distributed Link Aggregation (DLA); the EI units support
enhanced XRN, that is DDM, Distributed Resilient Routing (DRR).
Specifying the Stacking
VLAN of the Switch
You can use the command in the following table to specify the
stacking
VLAN of the
Switch.
Perform the following configuration in System View.
Table 61 Specifying the
Stacking
VLAN of the Switch
By default, the stacking VLAN is VLAN 4093.
You should specify the stacking VLAN before the Fabric is established.
Setting Unit IDs for
Switches
You can use the command in the following table to set unit IDs for Switches. Make
sure to set different unit IDs for different Switches in a Fabric. On the Switches that
support auto numbering, FTM will automatically number the Switches to constitute a
Fabric, so that each Switch has a unique unit ID in the Fabric.
sure to set different unit IDs for different Switches in a Fabric. On the Switches that
support auto numbering, FTM will automatically number the Switches to constitute a
Fabric, so that each Switch has a unique unit ID in the Fabric.
Perform the following configuration in System View.
Table 62 Setting unit IDs for Switches
n
If the modified unit ID does not exist in the Fabric, the Switch sets its priority to 5
and saves it in the unit Flash memory.
and saves it in the unit Flash memory.
Device
Configuration
Default Settings Comment
Switch
Specify the stacking
VLAN of the Switch
VLAN of the Switch
The stacking
VLAN is VLAN
4093
VLAN is VLAN
4093
You should specify the stacking
VLAN before the Fabric is
established.
VLAN before the Fabric is
established.
Set unit IDs for the
Switches
Switches
The unit ID of a
Switch is set to 1
Switch is set to 1
Make sure that you have set
different unit IDs to different
Switches, so that the Fabric can
operate normally after all the
Switches are interconnected.
different unit IDs to different
Switches, so that the Fabric can
operate normally after all the
Switches are interconnected.
Specify the Fabric
port of the Switch
port of the Switch
-
For 28-port Switch, the 27
th
28
th
port can be the Fabric port, for
52-port Switch, the 51
52-port Switch, the 51
st
, 52
nd
port
can be the Fabric port.
Set unit names for
the Switches
the Switches
-
-
Set a name for the
Fabric where the
Switches belong
Fabric where the
Switches belong
The Fabric name
of the Switches is
5500
of the Switches is
5500
Interconnected the Switches with
the same Fabric name to form a
Fabric.
the same Fabric name to form a
Fabric.
Set the
authentication
mode for the Fabric
authentication
mode for the Fabric
No authentication
mode is set on the
Switches
mode is set on the
Switches
Set the same authentication mode
on all the devices within the Fabric.
on all the devices within the Fabric.
Operation
Command
Specifying the stacking VLAN of the Switch
ftm stacking-vlan
vlan-id
Setting the stacking VLAN of the Switch to Default Value undo ftm stacking-vlan
Operation
Command
Set unit IDs for Switches
change unit-id <1-8> to {<1-8> |
auto-numbering }
auto-numbering }