Manualsbrain.com
  1. Manuais
  2. Marcas
  3. IBM
  4. Type 8720
  5. Manual Do Utilizador

IBM Type 8720 Manual Do Utilizador

Download
Página de 180
Removing
 
the
 
KVM
 
module
 
Complete
 
the
 
following
 
steps
 
to
 
remove
 
the
 
KVM
 
module
 
at
 
the
 
rear
 
of
 
the
 
BladeCenter
 
T
 
unit.
 
1.
   
Remove
 
the
 
keyboard,
 
mouse,
 
and
 
video
 
cables
 
if
 
any
 
are
 
connected.
 
2.
   
Fully
 
loosen
 
each
 
thumbscrew
 
counterclockwise.
 
3.
   
Hold
 
the
 
KVM
 
module
 
by
 
both
 
thumbscrews.
 
4.
   
Carefully
 
pull
 
the
 
KVM
 
module
 
outward
 
from
 
the
 
KVM
 
module
 
bay
 
until
 
you
 
feel
 
it
 
release.
 
5.
   
Remove
 
the
 
KVM
 
module
 
from
 
the
 
bay
 
and
 
set
 
it
 
aside.
 
6.
   
Within
 
1
 
minute,
 
install
 
a
 
new
 
KVM
 
module.
Installing
 
the
 
KVM
 
module
 
Complete
 
the
 
following
 
steps
 
to
 
install
 
the
 
KVM
 
module
 
at
 
the
 
rear
 
of
 
the
 
BladeCenter
 
T
 
unit
 
1.
   
Hold
 
the
 
KVM
 
module
 
by
 
both
 
thumbscrews.
 
Thumbscrew
Thumbscrew
CRT
MJR
MNR
System-status panel
  
  
2.
   
Position
 
the
 
KVM
 
module
 
into
 
the
 
rails
 
inside
 
the
 
KVM-module
 
bay.
 
3.
   
Push
 
the
 
KVM
 
module
 
into
 
the
 
bay
 
until
 
you
 
feel
 
it
 
stop.
 
Make
 
sure
 
that
 
it
 
is
 
snug.
 
4.
   
Turn
 
each
 
thumbscrew
 
clockwise
 
until
 
it
 
is
 
finger
 
tight.
 
If
 
you
 
use
 
a
 
screwdriver,
 
make
 
sure
 
that
 
you
 
do
 
not
 
overtighten
 
the
 
thumbscrews.
 
5.
   
Make
 
sure
 
that
 
the
 
power
 
LED
 
on
 
the
 
front
 
of
 
the
 
KVM
 
module
 
is
 
lit.
 
6.
   
Connect
 
any
 
peripheral
 
devices
 
that
 
you
 
want
 
to
 
use
 
at
 
this
 
time
 
(for
 
example,
 
keyboard,
 
mouse,
 
and
 
video
 
monitor).
 
 
Chapter
 
4.
 
Setting
 
up
 
the
 
BladeCenter
 
T
 
hardware
 
57