FieldServer FS-X20 Manual Do Utilizador

Start-up guide

Page 3

FS-X20 Series FieldServer Start-up Guide (07-2005)

2. Product Description

2.1. Specifications

Power requirements (power supply is external)
X20 power supply P/N 69155
Input voltage: 9-30VDC, 8W; 24VAC Floating. Voltage variation of ±10% tolerated.
Output voltage / current: 24VDC @ 0.5A
Physical Dimensions(excluding the external power supply)
(WxDxH):

3.82 x 4.08 x 1.7 inches (9.70 x 10.36 x 4.31 cm)

Weight:

0.8 lbs. (0.36 Kg)

Available Ports

1 x RJ45 / RS-232 serial connector
1 x RS-485 serial connector
1 x RJ45 10-BaseT Ethernet connector

Environment:
Operating Temperature:

0 – 60°C (32 – 140°F)

Humidity:

10 - 90% RH (non-condensing)

Approvals:

UL 916
ULC 916
FCC Tested to comply with FCC part 15
CE Marked

(Specifications subject to change without notice)

2.2. Mounting

The  FS-X20  Series  FieldServer  is  supplied
with  an  accessory  bag  which  allows
selection of adhesive feet (for standing on a
shelf)  or  mounting  plates  for  wall  or  panel
mount.    A  DIN  Rail  Mounting  Kit  (P/N  FS-
8915-28) may be ordered separately.

2.3. Wiring

The  110VAC  to  9VDC  or  24VDC/  power
supply  received  with  the  unit  needs  to  be
plugged  into  a  power  source  and  then
connected  to  the      back  of  the  FieldServer
using the SPA59136 connector.  This power
supply is designed to temporarily provide the
9-24V  100mA  required  by  the  FieldServer
during  testing  and  start-up.    Permanent  9-
30V, 100mA power will need to be provided
for continuous operation.

The  FS-X20  Series  FieldServer  is  shipped
as  either  a  FS-X20XX-01  in  which  case  the
RS-232 port is activated, or as a FS-X20XX-
02  in  which  case  the  RS-485  port  is
activated.

If  using  an  RS-232  RJ45  Serial  connection
then use one of the RJ45 cables to connect
from the appropriate port on the FieldServer

to  the  connection  adapter  provided  with  the
FieldServer or the Driver Kit.  Then plug the
connection adapter to the node.

If  using  RS-485  from  the  node  to  the  FS-
X2010, the + and - wire connections can be
used on the RS-485 port on the FieldServer.
For  the  FS-X2011,  LonWorks

enabled

modules,  the  orange  port  is  the  TP/FT-10
connection,  and  the  RS-485  connection
needs to be made via  the  serial  RJ-45 port.
To  change  between  RS-232  and  RS-485
connection,  it  is  necessary  to  modify
jumpers  on  the  internal  board.    Refer  to
eNote0017

for further information.

Ethernet

connections

simply

require

connection of a standard Cat5 UTP Ethernet
cable  with  an  RJ45  connector  between  the
FieldServer  and  the  network.    Note  that
when  connecting  the  FieldServer  directly  to
another  Ethernet  enabled  device  without
using  a  hub,  then  standard  Ethernet
principles  apply,  and  a  Crossover  cable
must be used.

Note that the USB port is not activated.

eNotes are available at