Campbell Hausfeld FP2049 Manual Do Utilizador

3. Only persons well acquainted with

these rules of safe operation should
be allowed to use the compressor.

4. Keep visitors away and NEVER allow

children in the work area.

5. Wear safety glasses

and use hearing
protection when
operating the pump
or unit.

6. Do not stand on or use the pump or

unit as a handhold.

7. Before each use, inspect compressed

air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.

8. Check all fasteners at frequent

intervals for proper tightness.

9. Keep fingers away from a running

compressor; fast moving and hot
parts will cause injury and/or burns.

10. If the equipment should start to

abnormally vibrate, STOP the
engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.

11. To reduce fire hazard, keep

engine/motor exterior free of oil,
solvent, or excessive grease.

13. Tanks rust from moisture build-up,

which weakens the tank. Make sure
to drain tank daily and inspect
periodically for unsafe conditions
such as rust formation and
corrosion.

14. Fast moving air will stir up dust and

debris which may be harmful. Release
air slowly when draining moisture or
depressurizing the compressor system.

15. Do not smoke when spraying paint,

insecticides, or other flammable
substances.

16. Use a face mask/

respirator when
spraying and spray in
a well ventilated area
to prevent health and
fire hazards.

17. Do not direct paint or other sprayed

material at the compressor. Locate
compressor as far away from the
spraying area as possible to
minimize overspray accumulation
on the compressor.

18. When spraying or cleaning with

solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.

It is extremely important to use the
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than 100°F.

A minimum clearance of 18 inches
between the compressor and a wall is
required because objects could obstruct
air flow.

1. This product is for use on a nominal

120 volt circuit and has a grounding
plug that looks like the plug illustrated
in Fig. 1. Make sure the product is
connected to an outlet having the
same configuration as the plug. This
product must be grounded. In the
event of an electrical short circuit,
grounding reduces risk of electrical
shock by providing an escape wire for
electric current. This product is
equipped with a cord having a
grounding wire with an appropriate
grounding plug. Plug must be plugged
into an outlet that is properly installed
and grounded in accordance with all
local codes and ordinances.

TEST

RESET

Grounding

Pin

Grounded Outlet

1

Cubierta con mango

FP204822AV

1

2 (a, b)

Ensamblaje del mango

FP204823AV

1

3

Manómetro del tanque

FP204012AV

1

4

Regulador

FP204013AV

1

5

Múltiple

FP204835AV

1

6

Válvula de seguridad

V-215102AV

1

7

Interruptor

FP204824AV

1

8

Llave de drenaje

D-1403

1

9

Ensamblaje de la bomba/motor FP204825AV

1

10

Presostato

FP204836AV

1

11

Kit de tubo de escape

FP204826AV

1

12

Tornillos de la tapa - 

Artículo estándar 

M6-1.0 x 20

de ferretería

4

13

Manguera de 7,6 m (25 pies)

MP302700AV

1

14

Juego de herramientas (5 piezas)FP204008AV

1

15

Válvula de chequeo

FP204827AV

1

16

Cubierta de almacenamiento  FP204828AV

1

17

Juego de etiqueta adhesiva 
(no se muestra)

FP204829AV

1

18 (a, b)

Kit de aislador

FP204830AV

1

19 (a, b)

Guarda de bomba/motor

FP204831AV

1

20

Filtro

FP204832AV

1

21

Patas de caucho

FP204833AV

1

22

Cordón eléctrico

FP204834AV

1

1

12

13

7

2a

14

2b

18a

18b

19a

19b

20

2b

16

11

4

5

8

21

10

22

15

6

9

3

-Número del modelo

Campbell Hausfeld / Attn: Parts Department

-Número de Serie (de haberlo) 

100 Production Drive

-Descripción y número del repuesto según la lista de repuestos

Harrison, OH  45030 U.S.A.