Cub Cadet ST228 Manual Do Utilizador
769-07532 P01
05/12
Quick Instructions to
Replace Trimmer Line
Replace Trimmer Line
For complete instructions,
refer to Line Installation
section of this manual.
refer to Line Installation
section of this manual.
Quick Instructions
to Start Engine
to Start Engine
For complete instructions, refer to
Starting/ Stopping Instructions section
of this manual.
Starting/ Stopping Instructions section
of this manual.
Quick Instructions to
Assemble Trimmers
Assemble Trimmers
For complete instructions, refer to the
Assembly Instructions section of this
manual.
Assembly Instructions section of this
manual.
Rotate the bump knob
clockwise until all line is
inside the cutting head.
clockwise until all line is
inside the cutting head.
Using a flat-head screwdriver,
insert the tip into the line dimple,
just under the exposed portion of
the line, and pull all the line out.
insert the tip into the line dimple,
just under the exposed portion of
the line, and pull all the line out.
Align the arrows on the
bump knob with the
spool cover eyelets.
bump knob with the
spool cover eyelets.
Using 16 ft. of 0.095 in. line; push both
ends through the holes in the bump knob
until they protrude through the eyelets.
ends through the holes in the bump knob
until they protrude through the eyelets.
Hold the spool cover, turn the bump
knob clockwise to wind the line around
the spool until about 5 in. is protruding
from each side of the cutting head.
knob clockwise to wind the line around
the spool until about 5 in. is protruding
from each side of the cutting head.
Start the unit and bump the cutting
head on the ground until the
desired cutting length is achieved.
head on the ground until the
desired cutting length is achieved.
Pull the line until approximately
8 ft. is visible on each side.
8 ft. is visible on each side.
IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
Read and understand all instruction, warning and danger labels on the unit.
Mix thoroughly in a separate fuel can:
– 2.6 fl. oz. of 2-cycle engine oil
– 1 gallon of unleaded gasoline
Place the unit on a level surface.
Fill fuel tank.
NOTE: Do not mix directly in the
engine fuel tank.
– 2.6 fl. oz. of 2-cycle engine oil
– 1 gallon of unleaded gasoline
Place the unit on a level surface.
Fill fuel tank.
NOTE: Do not mix directly in the
engine fuel tank.
Remove the cap and spacer
from the boom. Push the
bottom add-on into the
coupler. Turn the knob
clockwise to tighten.
from the boom. Push the
bottom add-on into the
coupler. Turn the knob
clockwise to tighten.
1 Gallon
2.6 oz
50:1
Press primer bulb 10 times.
Move choke lever to
Position 1.
Position 1.
Continue to squeeze
throttle control and
move the choke
lever to Position 3.
throttle control and
move the choke
lever to Position 3.
Move choke lever to
Position 2.
Position 2.
Pull the rope
5 times.
5 times.
Continue squeezing the
throttle control and run engine
for additional 60 seconds to
complete warm up.
throttle control and run engine
for additional 60 seconds to
complete warm up.
Pull starter rope 3 to 5 times.
Making sure to keep throttle
squeezed, run engine for
30-60 seconds to warm up.
Making sure to keep throttle
squeezed, run engine for
30-60 seconds to warm up.
Crouch in starting
position.
position.
DIDN’T START?
Repeat these instructions.
If engine still fails to start,
refer to the operator’s
manual for additional
starting and troubleshooting
information
5 X
Place the shield onto the mount bracket.
Securely screw the 4 shield screws through
the holes on the mount bracket and into the
shield. Make sure the screws are tightened
equally.
Securely screw the 4 shield screws through
the holes on the mount bracket and into the
shield. Make sure the screws are tightened
equally.
PRESS the lockout in;
SQUEEZE and HOLD throttle
control for ALL further steps.
SQUEEZE and HOLD throttle
control for ALL further steps.
Remove the screws and bottom clamp. Place
the D-handle over the shaft housing and onto
the bottom clamp. Move it a minimum of 6 inches
(15.24 cm) from the end of the shaft grip.
If pre-installed, loosen the screws just enough
to move it. Tighten the clamp screws evenly
until handle is secure.
the D-handle over the shaft housing and onto
the bottom clamp. Move it a minimum of 6 inches
(15.24 cm) from the end of the shaft grip.
If pre-installed, loosen the screws just enough
to move it. Tighten the clamp screws evenly
until handle is secure.
Min. 6"
E
s
p
a
ñ
o
l
—
P
a
g
e
1
3
E
n
g
li
s
h
—
P
a
g
e
1
F
ra
n
ç
a
is
—
P
a
g
e
7
ST228
2-Cycle Trimmer
Operator’s Manual
NEED HELP?
CALL 1–877-282-8684 IN U.S. OR 1–800–668–1238 IN CANADA